Savin 2235, 3502/3502p, 4502/4502p, 2545/2545p, 2245 Setting Originals on the Exposure Glass

Page 44

AdonisC2_ENcopy122F_FM.book Page 31 Thursday, February 15, 2001 3:23 PM

Setting Originals

Setting Originals

Limitation

❒Set originals after correction fluid and ink has completely dried. Not taking this precaution could mark the exposure glass and cause marks to be copied.

Note

❒Basically originals should be aligned to the rear left corner. However, some copy functions may produce different results de- pending on the direction of the originals. For details, see the expla- nations of each function.

Reference

⇒P.19 “Originals”.

Setting Originals on the Exposure Glass

A Lift the platen cover or the docu- ment feeder.

Important

❒Do not open the document feed- er with a force. Otherwise, the cover of the document feeder might open or be damaged.

Note

❒Be sure to open the document feeder by more than 30°. Other- wise the original size might not be detected correctly.

B Set the original face down on the exposure glass. The original should be aligned to the rear left corner.

1:Reference mark

2:Scale

Note

❒Start with the first page to be copied.

C Lower the platen cover or docu- ment feeder.

2

31

Image 44

Contents Zdsh000j.eps ⇒ P.237 Power Connection Means Power ON. c means Stand by FCC RequirementsSafety Information Safety During OperationPage How to Read this Manual SymbolsPreparation LimitationTable of Contents Job Preset Other Functions Preset Reduce/EnlargeBasic Functions Sort/Stack/Staple101 112116 121149 151156 161198 202206 207235 236238 239Page Machine Types What You Can Do with This Machine Copy Mode Series/Book Document Server ⇒ P.39 ⇒ P.37103 ⇒ P.77Guide To Components Bypass tray Right side cover Ventilation holeTo copy onto OHP transparencies and translucent paper Output Tray GuideTo copy onto normal paper and thick paper Options Control Panel Function Status indicator Clear/Stop keyNumber keys Function keysInitial copy display Display PanelDisplays and Key Operations Function menu Document Server initial displayFunction List Based on Options Set the paper of the same size KL in the paper trays Turning On the Power Turning On the Main PowerOperation switch right side of the control panel Main power switch left side of the ma- chinePress the operation switch to make the On indicator goes on Turning On the PowerTurning Off the Power Turning Off the Main Power Changing Modes Originals Metric versionInch version Non-recommended originals for the document feederSizes Detectable by the Auto Paper Select Sizes difficult to detectDocument feeder Missing Image AreaExposure glass Copy Paper Recommended Paper Sizes and TypesIfy the size. ⇒ P.60 Copying from the Bypass Tray Basics Direction-fixed paper or 2-sided paper Non-recommended Paper Paper StorageUsed Toner TonerToner Storage Basics Basic Procedure Make sure that the machine is in Copy modeMake sure that there are no previ- ous settings remaining Set your originalsSystem Reset Setting Originals Setting Originals on the Exposure GlassLift the platen cover or the docu- ment feeder Lower the platen cover or docu- ment feederSetting Originals Document Feeder Original OrientationStandard Orientation TurnSetting Special Originals Batch modePress the key Press the OK key Press the Batch keyMixed Size mode Setting Custom Size Originals Clear or Clear/Stop key, and then enter the value again Basic Functions Press the Lighter or Darker key to adjust the density Make sure that the Auto Image Den- sity key is selectedSelecting Original Type Setting Manual Paper Select Selecting Copy PaperAuto Paper Select Auto Paper Select Make sure that the Auto Paper Select key is selectedRotated copy Select the paper tray Auto Reduce/EnlargePress the Auto Reduce/Enlarge key Sort/Stack/Staple StackSort Shift Sort Press the Sort or Rotate Sort keyWhen the 2 Tray Finisher is installed Enter the number of copy sets with the number keysSet the original, then press the Start key After all originals are scanned, press the # keyEnter the number of copies with the number keys StackShift Stack Set the original in the same direction as the first one Staple Stapling position and original setting Sheet Finisher Tray FinisherSelect one of the stapling positions Sort/Stack/Staple⇒ P.51 Stapling position and original setting When Memory Reaches 0% To Remove the Paper from the Staple UnitPress the No key to resume scanning Press the Yes keyPunch HolesPunch hole positions Punchable paper sizes are as follows Select the Punch positionEnter the number of copy sets with the number keys Extender Open the bypass tray Adjust the guides to copy paper sizeCopying from the Bypass Tray When copying onto custom size paper Press the # keyCopying Press the OK key Set your originals and press the Start key When Copying onto OHP Transparencies or Thick PaperSelect OHP Sheet or Thick Paper Storing Your Settings ProgramsStoring a Program Deleting a ProgramMake sure the program settings Deleting a ProgramRepeat steps E and F in Storing a Program Press the Do not Register keyRecalling a Program Job Preset Press the Copy key Set up the next copy jobCancel key Press the To Printing keyEnergy Saver Mode Interrupt Copy Other FunctionsTo interrupt an original being fed Press the Interrupt keyOriginal Beeper Sample CopyTo interrupt copying after all originals have been fed Set your original Press the Start keyPress the Change Quantity key Press the Clear/Stop key when Copying is displayedPress the Continue key Preset Reduce/Enlarge Ratio % Paper sizePress the Enlarge or Reduce key Create Margin modePress the Reduce/Enlarge key Adjust the ratios with the n or o key ZoomEnter the ratio Press the Mag. Ratio keyEnter the desired ratio with the number keys Size Magnification Press the Reduce/Enlarge key Press the Specifid Ratio keyPress the OK key Set your original, then press the Start key