Panasonic PT-L592U manual Basic operation, Changing the input source

Page 19

Basic operation

Changing the input source

Projector

Remote control unit

or

The video signal input source and the corresponding audio signal input source can be changed in the order shown below each time the INPUT button on the projector control panel or the remote control unit is pressed. The input source selected is displayed on the screen for approximately five seconds.

The video signal from the input signal source which is connected to the S-VIDEO IN or VIDEO IN terminal will be projected.

At this time, the audio input will be switched to the signal from the input source which is connected to the AUDIO IN (L-R) terminals for S-VIDEO/VIDEO input. However, only one audio signal input system is available, so if you wish to change the audio input source, you will need to remove and insert the appropriate plugs.

The signal which is being input to the RGB IN connector for RGB 1 will be projected.

The audio signal output will be the signal which is being input to the AUDIO IN connector for RGB 1.

The signal which is being input to the RGB IN connector for RGB 2 will be projected.

The audio signal output will be the signal which is being input to the AUDIO IN connector for RGB 2.

NOTE:

The mode name for the currently-selected signal or the name of the signal format will be displayed directly underneath the on-screen display of the input signal source.

The on-screen display of the selected input source normally appears when projection starts, and also when the input source is being switched. However, if the input display setting (INPUT DISP) has been turned off, this on- screen display will not appear. (Refer to page 29.)

If the S-VIDEO IN and VIDEO IN terminals are both connected at the same time, the S-VIDEO IN signal input will automatically be given priority. If you wish to view the signal being input to the VIDEO IN terminal, disconnect the plug from the S-VIDEO IN terminal.

If the picture is not projected normally when an RGB signal is being input, you will need to switch the signal mode to match the input signal. (Refer to page 19.)

If S-VIDEO or VIDEO has been selected as the input signal source, it may be necessary to select the correct format which corresponds to the input signal. If the picture is not projected correctly, refer to page 20.

-18-

Image 19

Contents LCD Projector Features ContentsDear Panasonic Customer Important Safety Notice Setting-up Precautions with regard to safetyWhen using the projector Do not place any heavy objects on top of the projector If problems occur during useCleaning and maintenance Take particular care when replacing the lamp unitWipe the cabinet with a soft, dry cloth Precautions on handlingAbout condensation Side view Remote control unitLocation and function of each part Front viewTop and front ProjectorSide terminal board Back, bottom and right viewInserting the batteries Before using the remote control unitDo not do any of the following If facing the remote control unit toward the screen Operating range of the remote control unitPower button Main Power switch Turning the power on and offTurning on the power Turning off the powerFlexible translucent screen Rigid-type translucent screen Screen characteristics referenceScreen requirements Silver screen Beaded screenStandard setting-up dimensions Standard setting-up positionsProjection distance L Height from lower edge Minimum Adjusting the position of the projected picture Adjuster button Adjustable legs Setting the projector up horizontallyRetracting the adjustable legs Adjustment procedureAdjustment procedure for direct adjustment Adjusting the lensRear mounting Setting-up positions and changing the projection methodSetting procedure Front mountingChanging the input source Basic operationNo. of dots Switching the signal mode during RGB signal inputAdjusting the volume System format selection for S-VIDEO Video input signalsTurning off the sound Remote control unitDisplaying the on-screen menu Adjusting the picture to the desired setting BAL R BAL G BAL B Adjusting the white balanceAdjustment procedure for volume adjustment Adjusting the sound to the desired settingAdjustment procedure for horizontal position adjustment Adjusting the picture positionBottom blanking correction for the V-BLK-B Adjusting the blankingLeft-side blanking correction for the H-BLK-L Top blanking correction for the V-BLK-TAdjustment func Adjusting the horizontal amplitudeWhen increasing the horizontal amplitude When decreasing the horizontal amplitudeAdjusting the dot clock frequency About dot clock adjustmentAdjusting the clock phase Disabling the Power button of the remote control unit Using other useful functionsChanging the on-screen display language to another language Using the countdown timerUsing the lens retracting function Using the power save functionSetting procedure Example of connection to audio-visual equipment System configuration exampleVCR Computer Audio system Example of connection to a computerComputer for Pointer Click 1 button Wireless mouseExample of connection OperationBasic format Using the serial connectorPin layout and signal names for Serial connector Communication settingsAVL Control commandsCable specifications POFPossible cause IndicatorsCleaning the air filter Install the air filter cover Clean the air filter and the air filter clampsReplacing the lamp unit Lamp unit replacement periodLamp unit cover Fixing screw for the lamp unit cover Replacement procedureFixing screw for the lamp unit Page Problem Before asking for service, check the following pointsRGB HD/SYNC Audio Video Audio in L-R SpecificationsFCC Trademark AcknowledgementsDimensions