Panasonic PT-L592U System format selection for S-VIDEO Video input signals, Adjusting the volume

Page 21

<System format selection for S-VIDEO (VIDEO) input signals>

If S-VIDEO or VIDEO has been selected as the input signal source, there may be times where the signal format is not selected correctly, with the result that a normal picture is not projected. If this happens, select the correct signal format by the following procedure. The default setting is “AUTO”.

Setting procedure

1.Press the MENU button to display the MENU screen.

2.Press the “ ” and “ ” buttons to select “PICTURE”.

3.Press the “<” and “>” buttons to display the PICTURE screen.

4.Press the “ ” and “ ” buttons to select “TV-SYSTEM”.

5.Press the “<” and “>” buttons to select either “AUTO”, “NTSC”, “PAL”, “SECAM” or “NTSC 4.43”.

Select the appropriate signal format for the input signal while referring to the table below.

Horizontal scanning frequency [kHz] Vertical scanning frequency [Hz] Color subcarrier frequency [MHz]

AUTO	Automatically selects NTSC, PAL, SECAM or NTSC 4.43.
NTSC	3.58
15.7	60.00
NTSC 4.43	4.43
PAL	4.43
15.63	50.00
SECAM	4.25 or 4.41

NOTE:

The correct signal format may not be selected if, for instance, you are using a poor-quality signal source, such as a dubbed video tape. Switching the signal format may give better results in such cases.

The setting screen and the MENU screen can both be cleared by pressing the MENU button.

Adjusting the volume

The volume can be adjusted by pressing the VOL (+/-) buttons on the remote control unit.

If the “+” button is pressed, the volume will increase,

Remote control unitand if the "-" button is pressed, the volume will decrease.

NOTE:

If these buttons are pressed while the on-screen display for another function is currently on the screen, the volume will still be adjusted but the current volume setting and the volume bar display will not appear.

The volume can also be adjusted from an on-screen display menu. Refer to page 24 for details on how to do this.

The volume output level will remain displayed on the screen for approximately three seconds.

-20-

Image 21

Contents LCD Projector Contents FeaturesDear Panasonic Customer Important Safety Notice Precautions with regard to safety Setting-upWhen using the projector Cleaning and maintenance If problems occur during useTake particular care when replacing the lamp unit Do not place any heavy objects on top of the projectorPrecautions on handling Wipe the cabinet with a soft, dry clothAbout condensation Location and function of each part Remote control unitFront view Side viewTop and front ProjectorSide terminal board Back, bottom and right viewBefore using the remote control unit Inserting the batteriesDo not do any of the following If facing the remote control unit toward the screen Operating range of the remote control unitTurning on the power Turning the power on and offTurning off the power Power button Main Power switchScreen requirements Screen characteristics referenceSilver screen Beaded screen Flexible translucent screen Rigid-type translucent screenStandard setting-up positions Standard setting-up dimensionsProjection distance L Height from lower edge Minimum Adjusting the position of the projected picture Retracting the adjustable legs Setting the projector up horizontallyAdjustment procedure Adjuster button Adjustable legsAdjustment procedure for direct adjustment Adjusting the lensSetting procedure Setting-up positions and changing the projection methodFront mounting Rear mountingChanging the input source Basic operationNo. of dots Switching the signal mode during RGB signal inputAdjusting the volume System format selection for S-VIDEO Video input signalsRemote control unit Turning off the soundDisplaying the on-screen menu Adjusting the picture to the desired setting BAL R BAL G BAL B Adjusting the white balanceAdjustment procedure for volume adjustment Adjusting the sound to the desired settingAdjustment procedure for horizontal position adjustment Adjusting the picture positionLeft-side blanking correction for the H-BLK-L Adjusting the blankingTop blanking correction for the V-BLK-T Bottom blanking correction for the V-BLK-BWhen increasing the horizontal amplitude Adjusting the horizontal amplitudeWhen decreasing the horizontal amplitude Adjustment funcAbout dot clock adjustment Adjusting the dot clock frequencyAdjusting the clock phase Disabling the Power button of the remote control unit Using other useful functionsChanging the on-screen display language to another language Using the countdown timerUsing the lens retracting function Using the power save functionSetting procedure System configuration example Example of connection to audio-visual equipmentVCR Example of connection to a computer Computer Audio systemComputer for Example of connection Wireless mouseOperation Pointer Click 1 buttonPin layout and signal names for Serial connector Using the serial connectorCommunication settings Basic formatCable specifications Control commandsPOF AVLPossible cause IndicatorsCleaning the air filter Install the air filter cover Clean the air filter and the air filter clampsReplacing the lamp unit Lamp unit replacement periodReplacement procedure Lamp unit cover Fixing screw for the lamp unit coverFixing screw for the lamp unit Page Problem Before asking for service, check the following pointsRGB HD/SYNC Audio Video Audio in L-R SpecificationsFCC Trademark AcknowledgementsDimensions