Panasonic PT-L592U manual Adjusting the picture position

Page 26
Adjustment func- tion display

Adjusting the picture position

If the picture is not correctly positioned within the display area of the screen so that part of the edge of the picture does not appear, adjust the position of the picture.

The adjustment procedure below describes the on-screen displays when a signal is being input to the S-VIDEO IN terminal or the VIDEO IN terminal.

Adjustment procedure <for horizontal position adjustment>

1.

Press the MENU button to display the MENU screen.

2.

Press the “ ” and “ ” buttons to select “POSITION”.

3.Press the “<” and “>” buttons to display the POSITION screen.

NOTE:

If the STD (Standard) button is pressed while the POSITION screen at right is being displayed, the letters “STD” will be displayed in yellow in the top-right corner of the screen and all items displayed will be reset to the factory pre- settings. Furthermore, the values and bar displays for items which have returned to the factory pre-settings will be displayed in yellow.

4.Press the “ ” and “ ” buttons to select “H-POSI”.

To adjust the vertical position of the picture, select “V-POSI” instead.

5.Press the “<” and “>” buttons to display the H-POSI individual adjustment screen.

6.Continue pressing the “<” and “>” buttons to adjust the H-POSI setting. The

current setting will be displayed on the screen by numerals and a bar. The adjustment range is between 0 and 95.

Numeric adjustment level display

<When adjusting the horizontal position (H-POSI)>

Bar display

If the ">" button is pressed, the picture moves to the right.

If the “<” button is pressed, the picture moves to the left.

<When adjusting the vertical position (V-POSI)>

If the ">" button is pressed, the picture moves up.

If the "<" button is pressed, the picture moves down.

NOTE:

If approximately five seconds pass without any buttons being pressed while an individual adjustment screen is being displayed, the display will return to the POSITION screen.

Press the MENU button to return to the POSITION screen or to clear the MENU screen.

If the STD (Standard) button is pressed while one of the individual adjustment screens is being displayed, the value and the bar display will be appeared in yellow and only the item displayed will be reset to the factory pre- setting.

-25-

Image 26
Contents LCD Projector Dear Panasonic Customer ContentsFeatures Important Safety Notice When using the projector Precautions with regard to safetySetting-up Take particular care when replacing the lamp unit If problems occur during useCleaning and maintenance Do not place any heavy objects on top of the projectorAbout condensation Precautions on handlingWipe the cabinet with a soft, dry cloth Front view Remote control unitLocation and function of each part Side viewProjector Top and frontBack, bottom and right view Side terminal boardDo not do any of the following Before using the remote control unitInserting the batteries Operating range of the remote control unit If facing the remote control unit toward the screenTurning off the power Turning the power on and offTurning on the power Power button Main Power switchSilver screen Beaded screen Screen characteristics referenceScreen requirements Flexible translucent screen Rigid-type translucent screenProjection distance L Height from lower edge Minimum Standard setting-up positionsStandard setting-up dimensions Adjusting the position of the projected picture Adjustment procedure Setting the projector up horizontallyRetracting the adjustable legs Adjuster button Adjustable legsAdjusting the lens Adjustment procedure for direct adjustmentFront mounting Setting-up positions and changing the projection methodSetting procedure Rear mountingBasic operation Changing the input sourceSwitching the signal mode during RGB signal input No. of dotsSystem format selection for S-VIDEO Video input signals Adjusting the volumeDisplaying the on-screen menu Remote control unitTurning off the sound Adjusting the picture to the desired setting Adjusting the white balance BAL R BAL G BAL BAdjusting the sound to the desired setting Adjustment procedure for volume adjustmentAdjusting the picture position Adjustment procedure for horizontal position adjustmentTop blanking correction for the V-BLK-T Adjusting the blankingLeft-side blanking correction for the H-BLK-L Bottom blanking correction for the V-BLK-BWhen decreasing the horizontal amplitude Adjusting the horizontal amplitudeWhen increasing the horizontal amplitude Adjustment funcAdjusting the clock phase About dot clock adjustmentAdjusting the dot clock frequency Using other useful functions Disabling the Power button of the remote control unitUsing the countdown timer Changing the on-screen display language to another languageUsing the power save function Using the lens retracting functionSetting procedure VCR System configuration exampleExample of connection to audio-visual equipment Computer for Example of connection to a computerComputer Audio system Operation Wireless mouseExample of connection Pointer Click 1 buttonCommunication settings Using the serial connectorPin layout and signal names for Serial connector Basic formatPOF Control commandsCable specifications AVLIndicators Possible causeCleaning the air filter Clean the air filter and the air filter clamps Install the air filter coverLamp unit replacement period Replacing the lamp unitFixing screw for the lamp unit Replacement procedureLamp unit cover Fixing screw for the lamp unit cover Page Before asking for service, check the following points ProblemSpecifications RGB HD/SYNC Audio Video Audio in L-RTrademark Acknowledgements FCCDimensions