Panasonic PT-L592U manual Setting the projector up horizontally, Retracting the adjustable legs

Page 16

Setting the projector up horizontally

If the projector is not set up so that it is horizontal, it will not be possible to obtain a distortion-free picture. If placing the projector on top of a table or similar surface, carry out the following procedure below to ensure that no distortion of the picture occurs.

Adjustment procedure

1.Lift the front of the projector until the projector as a whole is horizontal. While holding it in this position, press the adjuster buttons under the sides of the projector (1 each at left and right). When the buttons are pressed, the left and right adjustable legs will drop down until they reach the setting-up surface.

NOTE:

Do not release the buttons until both legs have reached the setting-up surface.

Adjuster button

Adjustable legs

Adjuster button

2.Release the adjuster buttons. (The adjustable legs will lock as soon as the buttons are released.)

3.Turn the adjustable legs by hand in either direction

to make fine adjustments to the level of the projector so that the projector is perfectly horizontal.

NOTE:
The legs can be extended by up to	(60 mm).	UP to
		UP to

	If you try to extend them any further than this,	(60 mm)
	they will merely spin freely.	(60 mm)
	they will merely spin freely.

<Retracting the adjustable legs>

After lifting the front of the projector slightly, press and hold the adjuster buttons and then gently lower the projector.

NOTE:

Be sure to support the projector firmly while pressing the adjuster buttons. If the adjuster buttons are pressed without supporting the projector, the adjustable legs will suddenly unlock and the projector will fall down, which could damage the projector.

Adjuster button	Adjuster
	button
	Adjustable legs

-15-

Image 16

Contents LCD Projector Features ContentsDear Panasonic Customer Important Safety Notice Setting-up Precautions with regard to safetyWhen using the projector If problems occur during use Cleaning and maintenanceTake particular care when replacing the lamp unit Do not place any heavy objects on top of the projectorWipe the cabinet with a soft, dry cloth Precautions on handlingAbout condensation Remote control unit Location and function of each partFront view Side viewProjector Top and frontBack, bottom and right view Side terminal boardInserting the batteries Before using the remote control unitDo not do any of the following Operating range of the remote control unit If facing the remote control unit toward the screenTurning the power on and off Turning on the powerTurning off the power Power button Main Power switchScreen characteristics reference Screen requirementsSilver screen Beaded screen Flexible translucent screen Rigid-type translucent screenStandard setting-up dimensions Standard setting-up positionsProjection distance L Height from lower edge Minimum Adjusting the position of the projected picture Setting the projector up horizontally Retracting the adjustable legsAdjustment procedure Adjuster button Adjustable legsAdjusting the lens Adjustment procedure for direct adjustmentSetting-up positions and changing the projection method Setting procedureFront mounting Rear mountingBasic operation Changing the input sourceSwitching the signal mode during RGB signal input No. of dotsSystem format selection for S-VIDEO Video input signals Adjusting the volumeTurning off the sound Remote control unitDisplaying the on-screen menu Adjusting the picture to the desired setting Adjusting the white balance BAL R BAL G BAL BAdjusting the sound to the desired setting Adjustment procedure for volume adjustmentAdjusting the picture position Adjustment procedure for horizontal position adjustmentAdjusting the blanking Left-side blanking correction for the H-BLK-LTop blanking correction for the V-BLK-T Bottom blanking correction for the V-BLK-BAdjusting the horizontal amplitude When increasing the horizontal amplitudeWhen decreasing the horizontal amplitude Adjustment funcAdjusting the dot clock frequency About dot clock adjustmentAdjusting the clock phase Using other useful functions Disabling the Power button of the remote control unitUsing the countdown timer Changing the on-screen display language to another languageUsing the power save function Using the lens retracting functionSetting procedure Example of connection to audio-visual equipment System configuration exampleVCR Computer Audio system Example of connection to a computerComputer for Wireless mouse Example of connectionOperation Pointer Click 1 buttonUsing the serial connector Pin layout and signal names for Serial connectorCommunication settings Basic formatControl commands Cable specificationsPOF AVLIndicators Possible causeCleaning the air filter Clean the air filter and the air filter clamps Install the air filter coverLamp unit replacement period Replacing the lamp unitLamp unit cover Fixing screw for the lamp unit cover Replacement procedureFixing screw for the lamp unit Page Before asking for service, check the following points ProblemSpecifications RGB HD/SYNC Audio Video Audio in L-RTrademark Acknowledgements FCCDimensions