Panasonic PT-L592U manual Adjusting the sound to the desired setting

Page 25
Numeric adjustment level display
Adjustment func- tion display

Adjusting the sound to the desired setting

You can adjust the volume and balance to the desired settings.

Adjustment procedure <for volume adjustment>

1. Press the MENU button to display the MENU screen. 2. Press the “ ” and “ ” buttons to select “AUDIO”.

3.Press the “<” and “>” buttons to display the AUDIO screen.

NOTE:

If the STD (Standard) button is pressed while the AUDIO screen at right is being displayed, the letters “STD” will be displayed in yellow in the top-right corner of the screen and only the BALANCE setting will be reset to the factory pre- setting. Furthermore, if the BALANCE setting has returned to the factory pre- setting, the value and the bar display for the BALANCE setting will be displayed in yellow.

4.Press the “ ” and “ ” buttons to select “VOLUME’.

To adjust the balance, select “BALANCE” instead.

5.Press the “<” and “>” buttons to display the VOLUME individual adjustment screen.

6.Continue pressing the “<” and “>” buttons to adjust the volume setting. The current setting will be displayed on the screen by numerals and a bar.

The adjustment range is between 0 and 63.

(However, the adjustment range for the balance setting is -32–+31.)

While “VOLUME” is selected, the volume of the sound coming from the built-in speakers

and the output level of the signal from the

AUDIO OUT terminal will change.Bar display While “BALANCE” is selected, the left and

right balance of the sound coming from the built-in speaker and the output level of the signal from the AUDIO OUT terminal will change.

NOTE:

If approximately five seconds pass without any buttons being pressed while an individual adjustment screen is being displayed, the display will return to the AUDIO screen.

Press the MENU button to return to the AUDIO screen or to clear the MENU screen.

If the STD (Standard) button is pressed while the BALANCE individual adjustment screen is being displayed, the value and the bar display will be appeared in yellow and only the BALANCE setting will be reset to the factory pre-setting.

The “VOLUME” adjustment made from the AUDIO screen has the same effect as pressing the volume adjustment buttons (VOL ) on the remote control unit.

If the volume level is set to “0”, no sound will be output from the AUDIO OUT terminal.

-24-

Image 25
Contents LCD Projector Features ContentsDear Panasonic Customer Important Safety Notice Setting-up Precautions with regard to safetyWhen using the projector Cleaning and maintenance If problems occur during useTake particular care when replacing the lamp unit Do not place any heavy objects on top of the projectorWipe the cabinet with a soft, dry cloth Precautions on handlingAbout condensation Location and function of each part Remote control unitFront view Side viewTop and front ProjectorSide terminal board Back, bottom and right viewInserting the batteries Before using the remote control unitDo not do any of the following If facing the remote control unit toward the screen Operating range of the remote control unitTurning on the power Turning the power on and offTurning off the power Power button Main Power switchScreen requirements Screen characteristics referenceSilver screen Beaded screen Flexible translucent screen Rigid-type translucent screenStandard setting-up dimensions Standard setting-up positionsProjection distance L Height from lower edge Minimum Adjusting the position of the projected picture Retracting the adjustable legs Setting the projector up horizontallyAdjustment procedure Adjuster button Adjustable legsAdjustment procedure for direct adjustment Adjusting the lensSetting procedure Setting-up positions and changing the projection methodFront mounting Rear mountingChanging the input source Basic operationNo. of dots Switching the signal mode during RGB signal inputAdjusting the volume System format selection for S-VIDEO Video input signalsTurning off the sound Remote control unitDisplaying the on-screen menu Adjusting the picture to the desired setting BAL R BAL G BAL B Adjusting the white balanceAdjustment procedure for volume adjustment Adjusting the sound to the desired settingAdjustment procedure for horizontal position adjustment Adjusting the picture positionLeft-side blanking correction for the H-BLK-L Adjusting the blankingTop blanking correction for the V-BLK-T Bottom blanking correction for the V-BLK-BWhen increasing the horizontal amplitude Adjusting the horizontal amplitudeWhen decreasing the horizontal amplitude Adjustment funcAdjusting the dot clock frequency About dot clock adjustmentAdjusting the clock phase Disabling the Power button of the remote control unit Using other useful functionsChanging the on-screen display language to another language Using the countdown timerUsing the lens retracting function Using the power save functionSetting procedure Example of connection to audio-visual equipment System configuration exampleVCR Computer Audio system Example of connection to a computerComputer for Example of connection Wireless mouseOperation Pointer Click 1 buttonPin layout and signal names for Serial connector Using the serial connectorCommunication settings Basic formatCable specifications Control commandsPOF AVLPossible cause IndicatorsCleaning the air filter Install the air filter cover Clean the air filter and the air filter clampsReplacing the lamp unit Lamp unit replacement periodLamp unit cover Fixing screw for the lamp unit cover Replacement procedureFixing screw for the lamp unit Page Problem Before asking for service, check the following pointsRGB HD/SYNC Audio Video Audio in L-R SpecificationsFCC Trademark AcknowledgementsDimensions