Intel N270, FPC 5084 user manual Palette Snooping, PCI IDE BusMaster, OffBoard PCI/ISA IDE Card

Page 53

FPC 5084 User Manual

and Yes.

￿Palette Snooping

Some old graphic controllers need to “snoop” on the VGA palette, and then map it to their display as a way to provide boot information and VGA compatibility. This item allows such snooping to take place. Here are the options for your selection, Disabled and Enabled.

￿PCI IDE BusMaster

This item is a toggle for the built-in driver that allows the onboard IDE controller to perform DMA (Direct Memory Access) transfer. Here are the options for your selection, Disabled and Enabled.

￿OffBoard PCI/ISA IDE Card

This item is for any other non-onboard PCI/ISA IDE controller adapter. There are several options for your selection.

￿IRQ3/4/5/7/9/10/11/14/15

These items will allow you to assign each system interrupt a type, depending on the type of device using the interrupt. The option “Available” means the IRQ is going to assign automatically. Here are the options for your selection, Available and Reserved.

￿DMA Channel 0/1/3/5/6/7

These items will allow you to assign each DMA channel a type, depending on the type of device using the channel. The option “Available” means the channel is going to assign automatically. Here are the options for your selection, Available and Reserved.

AMI BIOS Setup Utility

43

Image 53
Contents FPC Disclaimers FCC Compliance Safety ApprovalsSafety Precautions Trademarks Acknowledgments Table of Contents Drivers Installation Memo Reliable and Stable Design General DescriptionMain CPU Board Specifications2 I/O System System SpecificationFPC Dimensions FPC I/O Outlets Packing List CF card Installation Chapter Hardware InstallationHardware Installation Serial Ports Interface Signal Name Ethernet Pin SignalPanel Mounting Mountings Panel/Wall/Desktop/VESAWall-Mounting Desktop-Mounting Hardware Installation VESA-ARM Mounting Vesa mounting Installation completed FPC Dram Installation FPC Wireless LAN Card Installation FPC Memo Page Navigation Keys StartingSystem Time/Date Main MenuAdvanced Menu Execute-Disable Bit Capability Configure advanced CPU settingsMax Cpuid Value Limit Hyper Threading TechnologyEnhanced C-States IDE ConfigurationSerial Port1 IRQ Serial Port1 AddressSerial Port2 Address Serial Port2 IRQSerial Port4 IRQ Serial Port4 AddressSystem Temperature/CPU Temperature Hardware Health ConfigurationAcpi Settings Video Power Down Mode APM ConfigurationPower Management/APM Power Button Mode Hard Disk Drive Power Down ModeSuspend Time Out Minute Throttle Slow Clock RatioAdvanced Resume Event Controls Resume On Ring Resume On RTC AlarmMPS Revision MPS ConfigurationActive State Power-Management PCI Express ConfigurationSB Pcie Ports Configuration USB 2.0 Controller Mode USB ConfigurationBios Ehci Hand-Off Legacy USB SupportPCI PnP Menu Clear Nvram PCI Latency TimerPlug & Play O/S Allocate IRQ to PCI VGAPCI IDE BusMaster Palette SnoopingOffBoard PCI/ISA IDE Card IRQ3/4/5/7/9/10/11/14/15Boot Menu Quiet Boot Boot Settings Configuration Quick BootAddOn ROM Display Mode Boot Num-LockHit ‘DEL’ Message Display Wait For ‘F1’ If ErrorBoot Device Priority Removable Drives Lan Boot Settings Configuration User Password Supervisor PasswordChange Supervisor Password Change User PasswordBoot Sector Virus Protection Chipset Menu Configure Dram Timing by SPD North Bridge Configuration Dram FrequencyBoot Graphic Adapter Priority Internal Graphics Mode SelectAMI Bios Setup Utility South Bridge Configuration Pcie Port Configuration Restore on AC Power LossUSB Function USB 2.0 ControllerSave Changes and Exit Exit MenuDiscard Changes and Exit Discard ChangesLoad Fail-Safe Defaults Load Optimal DefaultsSystem Chapter Drivers InstallationTouch Screen SpecificationDriver Installation- Windows XP FPC Installation of Drivers PenMount Touch screen Embedded O.SWindows XP Embedded Calibration Touch screen Windows CE.NET