Wacom 20WSX, DTZ-2000W manual Adjusting the display incline

Page 12

WARNING When operating the incline adjustment
	levers, Cintiq must be mounted on the
	stand with the stand feet resting on a	– B –
	stable, ﬂat surface. The stand is	– B –
	stable, ﬂat surface. The stand is
	spring-loaded and can snap back
	quickly, causing injury or damage if
	not operated properly.

After the display unit has been mounted on the stand, remove the foam blocks that lock the adjustment levers in place. Save these blocks with the other packaging materials; you will need them if in the future you want to ship Cintiq.

Adjusting the display incline

To adjust the display incline, face the front of the Cintiq pen display and grasp it on the left and right side at approximately the same height as the Cintiq stand adjustment levers. Use your ﬁngertips to gently pull the incline adjustment levers toward the display unit; this will release the stand’s clutch mechanism. Tilt the display to adjust the incline setting.

•To lower Cintiq, pull the left incline adjustment lever toward Cintiq and gently lower Cintiq to the desired incline angle. Release the lever to lock the stand in place.

•To raise Cintiq, pull the right incline adjustment lever toward Cintiq and gently raise Cintiq to the desired incline angle. Release the lever to lock the stand in place.

Note: The stand adjustment levers exhibit some natural play before the clutch mechanism engages. When adjusting the stand incline, set it slightly higher than you plan to work with, then lower the display to the desired position.

WARNING Before moving Cintiq, ﬁrst adjust the stand to its full upright position; this will reduce the spring tension so that the stand will not accidentally release and snap shut. If the display unit is in landscape orientation, use one hand to grasp the bottom of the display and with your other hand grasp the back of the stand. Be sure to lift on both the display and the stand so that the stand will not separate from the display when moving Cintiq. If Cintiq is in portrait orientation or has been locked to the stand with the rotation lock screws (see page 56), the stand will not separate from the display unit and Cintiq can be safely lifted by grasping the display unit with both hands.

Unpacking your Cintiq

Page 10

Image 12

Contents Page Page Introduction and Overview Precautions on USE and Handling Temperature and HumidityPhysical location EnvironmentHandling Cintiq pen display has a backlight which contains mercury HgPage Contents Contents Package contents Unpacking Your CintiqSetting up the Cintiq stand Incline adjustment leversBearing recess Front feet Rear feetUnpacking and mounting the Cintiq pen display Bearing hub Bearing recessAdjusting the display incline Adjusting rotation Using the pen holderRemoving Cintiq from the display stand Cintiq PEN Display Components Front viewRear view Installation System requirementsLCD monitor installation DVI-I connectorDVI-D connector VGA connectorApple ADC connector Mini-VGA port LCD monitor cabling diagram Select the option Browse MY Computer for Driver Software Installation Pen tablet installation USB cable installationPen tablet cabling diagram Software installation Next stepsUsing the pen Working with Your CintiqPen components Pen operations Working with the tablet controls Using the ExpressKeys Tips Using the Touch Strips Working with your Cintiq Setting up your work area Hints Customizing Opening the control panelCustomization basics Calibrating Cintiq Learning more about Cintiq Adjusting the LCD monitor Factory presets, auto-sync, and user settingsWorking with on screen display settings To automatically adjust, use the Reset option RESET. Provides two options Adjusting pitch and phase VGA only Power saving Computer mode Sync Video Power consumptionTroubleshooting Testing CintiqIf the Cintiq power LED does not light, check the following If there is no displayVerify that the tablet and Grip Pen are working Testing your input tools and pen display controls Testing the ExpressKeysTesting the Touch Strips Testing a pen PenAirbrush Display troubleshooting General display problemsVGA problems Pen tablet troubleshooting General problemsTroubleshooting Troubleshooting Troubleshooting Windows-speciﬁc problems Macintosh-speciﬁc problemsTechnical support options Obtaining driver downloads JapanAsia Paciﬁc English China Korea TaiwanCleaning AppendixCaring for Cintiq Replacing the pen tip To remove the old nibTo insert a new nib Optional display conﬁgurations To lock Cintiq to the display standLock screws Using an alternate mount or stand To attach Cintiq to a Vesa 100 mounting platformTo remove Cintiq from an alternate mounting platform Appendix Pen and digital ink capabilities in Windows Vista About the Windows Vista Tablet PC Input PanelUninstalling Cintiq WindowsMacintosh Product speciﬁcations Cintiq 20WSX model DTZ-2000W general speciﬁcationsLCD monitor Power adapter Pen tabletDisplay stand Grip pen model ZP-501EAccessories Purchasing parts and accessories Display adaptersRadio and television interference Federal Communications Commission FCC noticeCE declaration Warranty Warranty Service in the U.S.A. and Canada Warranty Service Outside of the U.S.A. and CanadaNorth and South America contact Wacom Technology Corporation Wacom Europe GmbH Wacom China CorporationTelephone UE-0364