Wacom DTZ-2100D manual Adjusting the Display Incline

Page 13

WARNING When operating the incline adjustment
	levers, Cintiq must be mounted on the
	stand with the stand feet resting on a	– B –
	stable, ﬂat surface. The stand is	– B –
	stable, ﬂat surface. The stand is
	spring-loaded and can snap back
	quickly, causing injury or damage if
	not operated properly.

After the display unit has been mounted on the stand, remove the foam blocks that lock the adjustment levers in place. Save these blocks with the other packaging materials; you will need them if in the future you want to ship Cintiq.

ADJUSTING THE DISPLAY INCLINE

To adjust the display incline, face the front of the Cintiq pen display and grasp it on the left and right side at approximately the same height as the Cintiq stand adjustment levers. Use your ﬁngertips to gently pull the incline adjustment levers toward the display unit; this will release the stand’s clutch mechanism. Tilt the display to adjust the incline setting.

•To lower Cintiq, pull the left incline adjustment lever toward Cintiq and gently lower Cintiq to the desired incline angle. Release the lever to lock the stand in place.

•To raise Cintiq, pull the right incline adjustment lever toward Cintiq and gently raise Cintiq to the desired incline angle. Release the lever to lock the stand in place.

Note: The stand adjustment levers exhibit some natural play before the clutch mechanism engages.

When adjusting the stand incline, set it slightly higher than you plan to work with, then lower the display to the desired position.

WARNING Before moving Cintiq, ﬁrst adjust the stand to its full upright position; this will reduce the spring tension so that the stand will not accidentally release and snap shut. If the display unit is in landscape orientation, use one hand to grasp the bottom of the display and with your other hand grasp the back of the stand. Be sure to lift on both the display and the stand so that the stand will not separate from the display when moving Cintiq. If Cintiq is in portrait orientation or has been locked to the stand with the rotation lock screws (see page 56 for details), the stand will not separate from the display unit and Cintiq can be safely lifted by grasping the display unit with both hands.

Unpacking your Cintiq

Page 11

Image 13

Contents Page Page Introduction and Overview Temperature and Humidity Precautions on USE and HandlingPhysical Location EnvironmentHandling UsageCintiq pen display has a backlight which contains mercury Hg Page Contents Appendix TroubleshootingUnpacking Your Cintiq Package ContentsIncline adjustment levers Setting UP the Cintiq StandBearing recess Front feet Rear feetBearing hub Bearing recess Unpacking and Mounting the Cintiq PEN DisplayAdjusting the Display Incline Using the PEN Holder Adjusting RotationRemoving Cintiq from the Display Stand Front View Cintiq PEN Display ComponentsRear View System Requirements InstallationDisplay Installation Apple ADC connector Mini-VGA port Display Cabling Diagram Select the option Browse MY Computer for Driver Software Installation USB Cable Installation PEN Tablet InstallationPEN Tablet USB Cabling Diagram Next steps Software InstallationEraser DuoSwitch Using the Grip PENTip Switch Working with Your CintiqBasic PEN Operations Working with your Cintiq Touch Strip Tablet ControlsTips Using ExpresskeysUsing the Touch Strips Setting UP Your Work Area Hints Opening the Control Panel CustomizingLearning More about Cintiq Customization Basics Tabs display customizable settings for the selected toolCalibrating Cintiq Factory PRESETS, AUTO-SYNC, and User Settings Adjusting the DisplayOn Screen Display OSD Settings Customizing Main Control ResetOSD Control LanguageCustomizing Adjusting Clock and Phase VGA only Computer mode Sync Power SavingVideo Power consumption Testing Cintiq TroubleshootingIf Cintiq’s power LED does not light, check the following If there is no displayVerify that the tablet and Grip Pen are working Testing the Expresskeys Testing Controls and Input ToolsTesting the Touch Strips Pen Testing a PENAirbrush General Display Problems Display TroubleshootingVGA Problems General Problems PEN Tablet TroubleshootingTroubleshooting Troubleshooting WINDOWS-SPECIFIC Problems Troubleshooting on MACINTOSH-SPECIFIC ProblemsTechnical Support Options Japan Obtaining Driver DownloadsAsia Paciﬁc English China Korea TaiwanAppendix CleaningCaring for Cintiq To remove the old nib Replacing the PEN TIPTo insert a new nib To lock Cintiq to the display stand Optional Display ConfigurationsLock screws To attach Cintiq to a Vesa 100 mounting platform Using AN Alternate Mount or StandTo remove Cintiq from an alternate mounting platform Appendix PEN and Digital INK Capabilities in Windows Vista About the Windows Vista Tablet PC Input Panel Windows Uninstalling CintiqMacintosh General Specifications Product SpecificationsDisplay PEN Tablet Power AdapterDisplay Stand Grip PEN Model ZP-501EAccessories Ordering Parts and Accessories Federal Communications Commission FCC Notice Radio and Television InterferenceCE Declaration Industry Canada Canada onlyIndustry Canada, Class B Warranty Warranty Service Outside of the U.S.A. and Canada Warranty Service in the U.S.A. and CanadaNorth and South America contact This page intentionally left blank This page intentionally left blank Wacom China Corporation Wacom Technology Corporation Wacom Europe GmbHTelephone UE-0308 E