Wacom DTZ-2100D manual Testing Controls and Input Tools, Testing the Expresskeys

Page 45

TESTING CONTROLS AND INPUT TOOLS

If the Grip Pen, or the Cintiq ExpressKeys or Touch Strips do not work as you expect, it is a good idea to first check the assigned functions or reset them to their default conditions. A quick way to reset a pen to its default settings is to remove it from the TOOL list by clicking on the list’s [ – ] button. After the pen has been removed, place it back onto the display screen surface and the pen will be re-added to the TOOL list with its default settings.

Open the Wacom Tablet control panel and click on the ABOUT button. In the dialog box that appears, click on the DIAGNOSE... button to open the DIAGNOSTICS dialog box. The DIAGNOSTICS dialog box displays dynamic information about the Cintiq pen display tablet and pen. This information is used when testing Cintiq and your input tool.

If more than one Cintiq unit is connected to your system, be sure to select the unit for which you are testing in the TABLET INFO column.

Note: When testing your tool buttons, if a button is set to POP-UPMENU or OPEN/RUN..., that function will occur when the button is pressed. In this case you may want to change that button’s function before testing.

TESTING THE EXPRESSKEYS

1.With the DIAGNOSTICS dialog box open, observe the TABLET INFO column as you test the ExpressKeys. If you have more than one Cintiq unit connected to your system, be sure to select the unit you are testing from the TABLET INFO column.

2.Test the keys by clicking them one at a time. Each time you press a key, its number will be displayed next to either the LEFT KEYS or RIGHT KEYS category, depending on which keys group you are testing. (See Using ExpressKeys on page 28 for details on the button numbers reported.)

When you are done, click the CLOSE button to exit the dialog box.

TESTING THE TOUCH STRIPS

1.With the DIAGNOSTICS dialog box open, observe the TABLET INFO column as you test each Touch Strip. If you have more than one Cintiq unit connected to your system, be sure to select the unit you are testing from the TABLET INFO column.

2.Slide your finger up or down along the entire length of the Touch Strip you want to test. As you touch and move your finger along the Touch Strip, a number will indicate the current finger position for the respective Touch Strip next to LEFT TOUCH STRIP or RIGHT TOUCH STRIP.

When you are done, click the CLOSE button to exit the dialog box.

Troubleshooting

Page 43

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Page Page Introduction and Overview Temperature and Humidity Precautions on USE and HandlingPhysical Location EnvironmentHandling UsageCintiq pen display has a backlight which contains mercury Hg Page Contents Appendix TroubleshootingUnpacking Your Cintiq Package ContentsIncline adjustment levers Setting UP the Cintiq StandBearing recess Front feet Rear feetBearing hub Bearing recess Unpacking and Mounting the Cintiq PEN DisplayAdjusting the Display Incline Using the PEN Holder Adjusting RotationRemoving Cintiq from the Display Stand Front View Cintiq PEN Display ComponentsRear View System Requirements InstallationDisplay Installation Apple ADC connector Mini-VGA port Display Cabling Diagram Select the option Browse MY Computer for Driver Software Installation PEN Tablet Installation USB Cable InstallationPEN Tablet USB Cabling Diagram Next steps Software InstallationEraser DuoSwitch Using the Grip PENTip Switch Working with Your CintiqBasic PEN Operations Working with your Cintiq Touch Strip Tablet ControlsTips Using ExpresskeysUsing the Touch Strips Setting UP Your Work Area Hints Customizing Opening the Control PanelLearning More about Cintiq Customization Basics Tabs display customizable settings for the selected toolCalibrating Cintiq Adjusting the Display Factory PRESETS, AUTO-SYNC, and User SettingsOn Screen Display OSD Settings Customizing Main Control ResetOSD Control LanguageCustomizing Adjusting Clock and Phase VGA only Power Saving Computer mode SyncVideo Power consumption Testing Cintiq TroubleshootingIf Cintiq’s power LED does not light, check the following If there is no displayVerify that the tablet and Grip Pen are working Testing Controls and Input Tools Testing the ExpresskeysTesting the Touch Strips Testing a PEN PenAirbrush General Display Problems Display TroubleshootingVGA Problems General Problems PEN Tablet TroubleshootingTroubleshooting Troubleshooting WINDOWS-SPECIFIC Problems Troubleshooting on MACINTOSH-SPECIFIC ProblemsTechnical Support Options Japan Obtaining Driver DownloadsAsia Pacific English China Korea TaiwanCleaning AppendixCaring for Cintiq Replacing the PEN TIP To remove the old nibTo insert a new nib Optional Display Configurations To lock Cintiq to the display standLock screws To attach Cintiq to a Vesa 100 mounting platform Using AN Alternate Mount or StandTo remove Cintiq from an alternate mounting platform Appendix PEN and Digital INK Capabilities in Windows Vista About the Windows Vista Tablet PC Input Panel Uninstalling Cintiq WindowsMacintosh Product Specifications General SpecificationsDisplay PEN Tablet Power AdapterDisplay Stand Grip PEN Model ZP-501EAccessories Ordering Parts and Accessories Federal Communications Commission FCC Notice Radio and Television InterferenceIndustry Canada Canada only CE DeclarationIndustry Canada, Class B Warranty Warranty Service in the U.S.A. and Canada Warranty Service Outside of the U.S.A. and CanadaNorth and South America contact This page intentionally left blank This page intentionally left blank Wacom Technology Corporation Wacom Europe GmbH Wacom China CorporationTelephone UE-0308 E
Top Page Image Contents