Toshiba B-SA4TP, B-SA4TM-GS12-QM-R, BSA4TMGS12QMR manual Appendix 4 Print Samples

Page 106

APPENDIX 4 PRINT SAMPLES

ENGLISH VERSION EO1-33048

APPENDIX 4 PRINT SAMPLES

APPENDIX 4 PRINT SAMPLES (Cont.)

EA4-2

Page 105 Page 107
Image 106
Page 105 Page 107
Contents SA4TP Series CE Compliance for EU only VorsichtSA4TP Series Waste Recycling information for users Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA3-1 EA1-1EA2-1 EA4-1Introduction Features Product OverviewAccessories Front View DimensionsAppearance Rear ViewOperation Panel InteriorOptions Option Name Type UsageProcedure Printer SetupSetup Flow ReferenceConnecting the Power Cord InstallationExample of US Type Raise the Release Lever and remove the Media Holder Left Loading the MediaTake out the Media Holder Ass’y from the printer Insert the Media Shaft into the core of a media rollFold the Release Lever to lock the Media Holder Left Place the Media Holder Ass’y into the printerClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Batch mode Strip mode OptionPress down the Release Bar to open the Strip Unit Label or Thin media Cut mode OptionTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Cont Gently close the Top Cover until it clicksConnecting the Printer to Your Host Computer Turning the Printer Fine Adjustment Refer to .3 ResetRefer to the B-SA4T Series Key Operation Parameter Setting How to Enter the System ModeSA4T Baud rate selection „ Serial RS-232C Interface Baud RateStop Bit „ Serial RS-232C Interface Data LengthParity READY/BUSY Flow Control„ LCD Message Language XON/XOFF„ Web Printer Function when using TCP/IP LAN „ Parallel Centronics Interface„ Plug & Play IP Address Setting TCP/IP Press the Pause key to enter the IP Address Setting Mode IP Address SettingThis section, how to set the IP address is described TCP/IPPrinter IP Address This parameter is to set an IP addressSubnet Mask Gateway IP AddressThis parameter is to set a Gateway IP address This parameter is to set a Subnet MaskSocket Port This parameter is to enable DhcpDhcp This parameter is to set a Dhcp client ID Dhcp Client IDAscii code and Hex. code correspondence table Introduction Installing the Printer DriversGeneral Description Installing the Printer Driver Parallel InterfaceWindows 95/98/Me Windows NT4.0 Windows 2000/XP USB Interface Windows 98/MeE2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 95/98/MEWindows NT4.0/2000/XP Deleting a LAN PortPrinter Driver Upgrades OthersUsing the Printer Driver Print Test AdjustmentPrint Method When using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment 3ADJUST SETReverse Feed Amount Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentPosition and Print When setting +0.0 mmTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting -50.0 mm When setting +50.0 mmPrint Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Sensor type is displayedSelect the sensor to be adjusted by using the Feed key Press the Pause key to enter the Sensor Adjustment Mode Feed and Pause keys„ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Manual Threshold Setting „ Storing a No Media Level VoltageBlack Mark Sensor Feed Gap Sensor Used to stop printing temporarily On Line OperationOperation Panel Used to restart printingOperation ResetPress and hold the Restart key for 3 seconds or longer Cleaning MaintenancePrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Same way, clean the outside of the Cutter Blade Optional Cutter Module 1. Open the Front CoverBacking Paper Feed Roller Strip Roller Guide Roller Error Messages TroubleshootingRestart key Error Messages Problems/Cause Possible Problems Possible Problems Causes SolutionsRemoving Jammed Media Do not use any tool that may damage the Print HeadThis section describes the printer specifications Printer SpecificationsModel Mail 4STATE Customer CODE, RSS14 Media Type Supply SpecificationsMedia LabelLabel Detection Area of the Transmissive SensorTag paper with square holes Detection Area of the Reflective Sensor Effective Print AreaRecommended Media and Ribbon Types RibbonMedia type Description Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Media type Vellum paper and labelAppendix 1 Messages and Leds Symbols in the messageROM Dhcp client is being initialized When the Dhcp function is enabledBase LAN Board is being initialised Printer did not succeed in writing dataFollowing message appears Appendix 2 Interface Parallel interface CentronicsConnector PINIEEE802.3 10BASE-T/100BASE-TX SA704-RFID-U1-EU SA704-RFID-U1-USAwid MPR-1510A-RM Awid MPR-1580A-RMWireless LAN Option SnmpWhen purchasing the power cord Appendix 3 Power CordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digitsCustomer bar code UPC-A+5 digitsIndustrial 2 KIX CodeAppendix 5 Glossaries Media and ribbon Device used to remove labels from the backing paperUSB Universal Serial Bus Index Index EO1-33048
Related manuals
Manual 45 pages 54.11 Kb
Top Page Image Contents