Toshiba BSA4TMGS12QMR, B-SA4TM-GS12-QM-R, B-SA4TP Appearance, Dimensions, Front View, Rear View

Page 11

1. PRODUCT OVERVIEW

ENGLISH VERSION EO1-33048

1.4 Appearance

1.4 Appearance

The names of the parts or units introduced in this section are used in the following chapters.

238 (9.4)

339 (13.3)

1.4.1 Dimensions

332

(13.1)

1.4.2 Front View

Ribbon Cover

Top Cover

LCD Message

Display

Operation Panel

Power Switch

O: OFF

I: ON

1.4.3 Rear View

Supply Window

AC Power Inlet

Dimensions in mm (inches)

Top Cover

Release Button

Media Outlet

Front Cover

RS-232C Serial Interface Connector (Option)

Wireless LAN Interface Board (Option)

Parallel Interface Connector (Centronics)

USB Interface

Connector

LAN Interface

Connector

E1- 3

Image 11

Contents SA4TP Series Vorsicht CE Compliance for EU onlySA4TP Series Waste Recycling information for users Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Product Overview Introduction FeaturesAccessories Rear View DimensionsAppearance Front ViewInterior Operation PanelOption Name Type Usage OptionsReference Printer SetupSetup Flow ProcedureExample of US Type InstallationConnecting the Power Cord Insert the Media Shaft into the core of a media roll Loading the MediaTake out the Media Holder Ass’y from the printer Raise the Release Lever and remove the Media Holder LeftPlace the Media Holder Ass’y into the printer Fold the Release Lever to lock the Media Holder LeftClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Strip mode Option Batch modePress down the Release Bar to open the Strip Unit Tag paper or Thick paper Cut mode OptionLabel or Thin media Loading the Ribbon Open the Ribbon Cover Gently close the Top Cover until it clicks ContConnecting the Printer to Your Host Computer Turning the Printer Refer to the B-SA4T Series Key Operation Refer to .3 ResetFine Adjustment SA4T How to Enter the System ModeParameter Setting Baud rate selection Baud Rate „ Serial RS-232C InterfaceParity „ Serial RS-232C Interface Data LengthStop Bit XON/XOFF Flow Control„ LCD Message Language READY/BUSY„ Parallel Centronics Interface „ Web Printer Function when using TCP/IP LAN„ Plug & Play IP Address Setting TCP/IP TCP/IP IP Address SettingThis section, how to set the IP address is described Press the Pause key to enter the IP Address Setting ModeThis parameter is to set an IP address Printer IP AddressThis parameter is to set a Subnet Mask Gateway IP AddressThis parameter is to set a Gateway IP address Subnet MaskDhcp This parameter is to enable DhcpSocket Port Ascii code and Hex. code correspondence table Dhcp Client IDThis parameter is to set a Dhcp client ID General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer DriverWindows 95/98/Me Windows NT4.0 Windows 2000/XP Windows 98/Me USB InterfaceE2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding a LAN Port Windows 95/98/ME Adding/Deleting a LAN PortDeleting a LAN Port Windows NT4.0/2000/XPOthers Printer Driver UpgradesUsing the Printer Driver Print Method AdjustmentPrint Test When using an optional Cutter Module or Strip Module 3ADJUST SET Position and Print Tone Fine AdjustmentCoordinate Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Reverse Feed Amount Fine AdjustmentTone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting +50.0 mm When setting -50.0 mmPrint Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Sensor type is displayed Threshold SettingSelect the sensor to be adjusted by using the Feed key Feed and Pause keys Press the Pause key to enter the Sensor Adjustment Mode„ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Storing a No Media Level Voltage „ Manual Threshold SettingBlack Mark Sensor Feed Gap Sensor Used to restart printing On Line OperationOperation Panel Used to stop printing temporarilyPress and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Print Head/Platen/ Sensors Covers and Panels Optional Cutter Module 1. Open the Front Cover Same way, clean the outside of the Cutter BladeBacking Paper Feed Roller Strip Roller Guide Roller Restart key TroubleshootingError Messages Error Messages Problems/Cause Possible Problems Causes Solutions Possible ProblemsDo not use any tool that may damage the Print Head Removing Jammed MediaModel Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Label Supply SpecificationsMedia Media TypeTag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective SensorMedia type Description RibbonRecommended Media and Ribbon Types Media type Vellum paper and label Care/Handling of Media and RibbonRibbon type Description Combination of Media and RibbonROM Symbols in the messageAppendix 1 Messages and Leds Printer did not succeed in writing data When the Dhcp function is enabledBase LAN Board is being initialised Dhcp client is being initializedFollowing message appears Parallel interface Centronics Appendix 2 InterfacePIN ConnectorIEEE802.3 10BASE-T/100BASE-TX Awid MPR-1580A-RM SA704-RFID-U1-USAwid MPR-1510A-RM SA704-RFID-U1-EUSnmp Wireless LAN OptionAt least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeAppendix 5 Glossaries USB Universal Serial Bus Device used to remove labels from the backing paperMedia and ribbon Index Index EO1-33048

Related manuals

Manual 45 pages 54.11 Kb