Toshiba B-SA4TM-GS12-QM-R, B-SA4TP, BSA4TMGS12QMR How to Enter the System Mode, Parameter Setting

Page 30

2. PRINTER SETUP

ENGLISH VERSION EO1-33048

2.7 Setting an Operating Environment

2.7.1How to Enter the System Mode

ONLINE

B-SA4T V1.0

P

This section describes how to enter the System Mode.

1.Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display.

2.Press the [PAUSE] key to pause the printer.

PAUSE

B-SA4T V1.0

R

3.Hold down the [RESTART] key for three seconds until “<1>RESET” is displayed.

4.Press the [FEED] key, and “<2>PARAMETER SET” appears on the LCD Message Display.

NOTE:

2.7.2 Parameter Setting

<2>PARAMETER SET

P

If the [PAUSE] key is pressed with “<1>RESET” being displayed, the printer will turn to an idle state and the message will change to “ONLINE”.

In this section, how to select a language and how to set the communication parameters are described. When further information is required, refer to the B-SA4T Series Key Operation Specification.

While “<2>PARAMETER SET” is displayed on the LCD Message Display, press the [PAUSE] key to enter the Parameter Setting Mode.

E2-17

Image 30

Contents SA4TP Series CE Compliance for EU only VorsichtSA4TP Series Waste Recycling information for users Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA3-1 EA1-1EA2-1 EA4-1Introduction Features Product OverviewAccessories Front View DimensionsAppearance Rear ViewOperation Panel InteriorOptions Option Name Type UsageProcedure Printer SetupSetup Flow ReferenceInstallation Connecting the Power CordExample of US Type Raise the Release Lever and remove the Media Holder Left Loading the MediaTake out the Media Holder Ass’y from the printer Insert the Media Shaft into the core of a media rollFold the Release Lever to lock the Media Holder Left Place the Media Holder Ass’y into the printerClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Batch mode Strip mode OptionPress down the Release Bar to open the Strip Unit Cut mode Option Label or Thin mediaTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Cont Gently close the Top Cover until it clicksConnecting the Printer to Your Host Computer Turning the Printer Refer to .3 Reset Fine AdjustmentRefer to the B-SA4T Series Key Operation How to Enter the System Mode Parameter SettingSA4T Baud rate selection „ Serial RS-232C Interface Baud Rate„ Serial RS-232C Interface Data Length Stop BitParity READY/BUSY Flow Control„ LCD Message Language XON/XOFF„ Web Printer Function when using TCP/IP LAN „ Parallel Centronics Interface„ Plug & Play IP Address Setting TCP/IP Press the Pause key to enter the IP Address Setting Mode IP Address SettingThis section, how to set the IP address is described TCP/IPPrinter IP Address This parameter is to set an IP addressSubnet Mask Gateway IP AddressThis parameter is to set a Gateway IP address This parameter is to set a Subnet MaskThis parameter is to enable Dhcp Socket PortDhcp Dhcp Client ID This parameter is to set a Dhcp client IDAscii code and Hex. code correspondence table Installing the Printer Drivers IntroductionGeneral Description Installing the Printer Driver Parallel InterfaceWindows 95/98/Me Windows NT4.0 Windows 2000/XP USB Interface Windows 98/MeE2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 95/98/MEWindows NT4.0/2000/XP Deleting a LAN PortPrinter Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestPrint Method When using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment 3ADJUST SETReverse Feed Amount Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentWhen setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting -50.0 mm When setting +50.0 mmPrint Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Sensor type is displayedSelect the sensor to be adjusted by using the Feed key Press the Pause key to enter the Sensor Adjustment Mode Feed and Pause keys„ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Manual Threshold Setting „ Storing a No Media Level VoltageBlack Mark Sensor Feed Gap Sensor Used to stop printing temporarily On Line OperationOperation Panel Used to restart printingReset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Same way, clean the outside of the Cutter Blade Optional Cutter Module 1. Open the Front CoverBacking Paper Feed Roller Strip Roller Guide Roller Troubleshooting Error MessagesRestart key Error Messages Problems/Cause Possible Problems Possible Problems Causes SolutionsRemoving Jammed Media Do not use any tool that may damage the Print HeadPrinter Specifications This section describes the printer specificationsModel Mail 4STATE Customer CODE, RSS14 Media Type Supply SpecificationsMedia LabelDetection Area of the Transmissive Sensor LabelTag paper with square holes Detection Area of the Reflective Sensor Effective Print AreaRibbon Recommended Media and Ribbon TypesMedia type Description Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Media type Vellum paper and labelSymbols in the message Appendix 1 Messages and LedsROM Dhcp client is being initialized When the Dhcp function is enabledBase LAN Board is being initialised Printer did not succeed in writing dataFollowing message appears Appendix 2 Interface Parallel interface CentronicsConnector PINIEEE802.3 10BASE-T/100BASE-TX SA704-RFID-U1-EU SA704-RFID-U1-USAwid MPR-1510A-RM Awid MPR-1580A-RMWireless LAN Option SnmpAppendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digitsCustomer bar code UPC-A+5 digitsIndustrial 2 KIX CodeAppendix 5 Glossaries Device used to remove labels from the backing paper Media and ribbonUSB Universal Serial Bus Index Index EO1-33048

Related manuals

Manual 45 pages 54.11 Kb