Toshiba B-SA4TP, B-SA4TM-GS12-QM-R, BSA4TMGS12QMR manual E2-36

Page 49

2. PRINTER SETUP

ENGLISH VERSION EO1-33048

2.8 Installing the Printer Drivers

(3)Select “Search for the best driver for your device. (Recommended)”.

Mark the “Specify a location” checkbox, then click on the [Browse] button. Specify “\driver\WinMe-9x” folder, then click on the [Next] button.

(4) Check to see that the “USB Printing Support” driver is detected, then click on the [Next] button.

E2-36

Image 49

Contents SA4TP Series Vorsicht CE Compliance for EU onlySA4TP Series Waste Recycling information for users Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA2-1 EA1-1EA3-1 EA4-1Product Overview Introduction FeaturesAccessories Appearance DimensionsFront View Rear ViewInterior Operation PanelOption Name Type Usage OptionsSetup Flow Printer SetupProcedure ReferenceConnecting the Power Cord InstallationExample of US Type Take out the Media Holder Ass’y from the printer Loading the MediaRaise the Release Lever and remove the Media Holder Left Insert the Media Shaft into the core of a media rollPlace the Media Holder Ass’y into the printer Fold the Release Lever to lock the Media Holder LeftClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Strip mode Option Batch modePress down the Release Bar to open the Strip Unit Label or Thin media Cut mode OptionTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Gently close the Top Cover until it clicks ContConnecting the Printer to Your Host Computer Turning the Printer Fine Adjustment Refer to .3 ResetRefer to the B-SA4T Series Key Operation Parameter Setting How to Enter the System ModeSA4T Baud rate selection Baud Rate „ Serial RS-232C InterfaceStop Bit „ Serial RS-232C Interface Data LengthParity „ LCD Message Language Flow ControlREADY/BUSY XON/XOFF„ Parallel Centronics Interface „ Web Printer Function when using TCP/IP LAN„ Plug & Play IP Address Setting TCP/IP This section, how to set the IP address is described IP Address SettingPress the Pause key to enter the IP Address Setting Mode TCP/IPThis parameter is to set an IP address Printer IP AddressThis parameter is to set a Gateway IP address Gateway IP AddressSubnet Mask This parameter is to set a Subnet MaskSocket Port This parameter is to enable DhcpDhcp This parameter is to set a Dhcp client ID Dhcp Client IDAscii code and Hex. code correspondence table Introduction Installing the Printer DriversGeneral Description Parallel Interface Installing the Printer DriverWindows 95/98/Me Windows NT4.0 Windows 2000/XP Windows 98/Me USB InterfaceE2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding a LAN Port Windows 95/98/ME Adding/Deleting a LAN PortDeleting a LAN Port Windows NT4.0/2000/XPOthers Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentPrint Method When using an optional Cutter Module or Strip Module 3ADJUST SET Position and Print Tone Fine AdjustmentCut/Strip Position Fine Adjustment Feed Amount Fine AdjustmentReverse Feed Amount Fine Adjustment Coordinate Fine AdjustmentPosition and Print When setting +0.0 mmTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting +50.0 mm When setting -50.0 mmPrint Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Sensor type is displayed Threshold SettingSelect the sensor to be adjusted by using the Feed key Feed and Pause keys Press the Pause key to enter the Sensor Adjustment Mode„ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Storing a No Media Level Voltage „ Manual Threshold SettingBlack Mark Sensor Feed Gap Sensor Operation Panel On Line OperationUsed to stop printing temporarily Used to restart printingOperation ResetPress and hold the Restart key for 3 seconds or longer Cleaning MaintenancePrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Optional Cutter Module 1. Open the Front Cover Same way, clean the outside of the Cutter BladeBacking Paper Feed Roller Strip Roller Guide Roller Error Messages TroubleshootingRestart key Error Messages Problems/Cause Possible Problems Causes Solutions Possible ProblemsDo not use any tool that may damage the Print Head Removing Jammed MediaThis section describes the printer specifications Printer SpecificationsModel Mail 4STATE Customer CODE, RSS14 Media Supply SpecificationsMedia Type LabelLabel Detection Area of the Transmissive SensorTag paper with square holes Effective Print Area Detection Area of the Reflective SensorRecommended Media and Ribbon Types RibbonMedia type Description Ribbon type Description Care/Handling of Media and RibbonCombination of Media and Ribbon Media type Vellum paper and labelAppendix 1 Messages and Leds Symbols in the messageROM Base LAN Board is being initialised When the Dhcp function is enabledDhcp client is being initialized Printer did not succeed in writing dataFollowing message appears Parallel interface Centronics Appendix 2 InterfacePIN ConnectorIEEE802.3 10BASE-T/100BASE-TX Awid MPR-1510A-RM SA704-RFID-U1-USSA704-RFID-U1-EU Awid MPR-1580A-RMSnmp Wireless LAN OptionWhen purchasing the power cord Appendix 3 Power CordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples JAN13, EAN13 Interleaved 2EAN13+2 digits EAN13+5 digitsIndustrial 2 UPC-A+5 digitsCustomer bar code KIX CodeAppendix 5 Glossaries Media and ribbon Device used to remove labels from the backing paperUSB Universal Serial Bus Index Index EO1-33048

Related manuals

Manual 45 pages 54.11 Kb