Toshiba B-SA4TM-GS12-QM-R, B-SA4TP, BSA4TMGS12QMR manual Plug & Play

Page 36

2. PRINTER SETUP

ENGLISH VERSION EO1-33048

2.7 Setting an Operating Environment

2.7.2Parameter Setting (Cont.)

Plug & Play

This parameter is to enable or disable the plug & play function.

As “OFF” has been chosen as default, change it when this function is used.

If the printer and the PC are connected by USB, plug & play will be automatically enabled, regardless of the setting of this parameter.

						<2>PARAMETER SET
						PLUG & PLAY	OFF

	[RESTART]					PLUG & PLAY	OFF

		[FEED]
		[FEED]				PLUG & PLAY	ON

After making a choice, press the [PAUSE] key.

E2-23

Image 36

Contents SA4TP Series CE Compliance for EU only VorsichtSA4TP Series Waste Recycling information for users Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA1-1 EA2-1EA3-1 EA4-1Introduction Features Product OverviewAccessories Dimensions AppearanceFront View Rear ViewOperation Panel InteriorOptions Option Name Type UsagePrinter Setup Setup FlowProcedure ReferenceInstallation Connecting the Power CordExample of US Type Loading the Media Take out the Media Holder Ass’y from the printerRaise the Release Lever and remove the Media Holder Left Insert the Media Shaft into the core of a media rollFold the Release Lever to lock the Media Holder Left Place the Media Holder Ass’y into the printerClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Batch mode Strip mode OptionPress down the Release Bar to open the Strip Unit Cut mode Option Label or Thin mediaTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Cont Gently close the Top Cover until it clicksConnecting the Printer to Your Host Computer Turning the Printer Refer to .3 Reset Fine AdjustmentRefer to the B-SA4T Series Key Operation How to Enter the System Mode Parameter SettingSA4T Baud rate selection „ Serial RS-232C Interface Baud Rate„ Serial RS-232C Interface Data Length Stop BitParity Flow Control „ LCD Message LanguageREADY/BUSY XON/XOFF„ Web Printer Function when using TCP/IP LAN „ Parallel Centronics Interface„ Plug & Play IP Address Setting TCP/IP IP Address Setting This section, how to set the IP address is describedPress the Pause key to enter the IP Address Setting Mode TCP/IPPrinter IP Address This parameter is to set an IP addressGateway IP Address This parameter is to set a Gateway IP addressSubnet Mask This parameter is to set a Subnet MaskThis parameter is to enable Dhcp Socket PortDhcp Dhcp Client ID This parameter is to set a Dhcp client IDAscii code and Hex. code correspondence table Installing the Printer Drivers IntroductionGeneral Description Installing the Printer Driver Parallel InterfaceWindows 95/98/Me Windows NT4.0 Windows 2000/XP USB Interface Windows 98/MeE2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 95/98/MEWindows NT4.0/2000/XP Deleting a LAN PortPrinter Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestPrint Method When using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment 3ADJUST SETFeed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentReverse Feed Amount Fine Adjustment Coordinate Fine AdjustmentWhen setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting -50.0 mm When setting +50.0 mmPrint Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Sensor type is displayedSelect the sensor to be adjusted by using the Feed key Press the Pause key to enter the Sensor Adjustment Mode Feed and Pause keys„ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Manual Threshold Setting „ Storing a No Media Level VoltageBlack Mark Sensor Feed Gap Sensor On Line Operation Operation PanelUsed to stop printing temporarily Used to restart printingReset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Same way, clean the outside of the Cutter Blade Optional Cutter Module 1. Open the Front CoverBacking Paper Feed Roller Strip Roller Guide Roller Troubleshooting Error MessagesRestart key Error Messages Problems/Cause Possible Problems Possible Problems Causes SolutionsRemoving Jammed Media Do not use any tool that may damage the Print HeadPrinter Specifications This section describes the printer specificationsModel Mail 4STATE Customer CODE, RSS14 Supply Specifications MediaMedia Type LabelDetection Area of the Transmissive Sensor LabelTag paper with square holes Detection Area of the Reflective Sensor Effective Print AreaRibbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Media type Vellum paper and labelSymbols in the message Appendix 1 Messages and LedsROM When the Dhcp function is enabled Base LAN Board is being initialisedDhcp client is being initialized Printer did not succeed in writing dataFollowing message appears Appendix 2 Interface Parallel interface CentronicsConnector PINIEEE802.3 10BASE-T/100BASE-TX SA704-RFID-U1-US Awid MPR-1510A-RMSA704-RFID-U1-EU Awid MPR-1580A-RMWireless LAN Option SnmpAppendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples Interleaved 2 JAN13, EAN13EAN13+2 digits EAN13+5 digitsUPC-A+5 digits Industrial 2Customer bar code KIX CodeAppendix 5 Glossaries Device used to remove labels from the backing paper Media and ribbonUSB Universal Serial Bus Index Index EO1-33048

Related manuals

Manual 45 pages 54.11 Kb