D-Link DVG-6008S Recorded Voice File, Adsl PPPoE Settings, Select a PPPoE, PPPoE Account Settings

Page 16

ADSL PPPoE Settings

NOTE: Complete PPPoE settings should include: Select PPPoE (Option 3 of 114), PPPoE account (121) and PPPoE password (122).

Please contact your local Internet Service Provider (ISP) if you have any questions.

Select a PPPoE

After entering IVR mode, dial 114.

After hearing “Enter value”, dial 3 (to select PPPoE).

PPPoE Account Settings

After entering IVR mode, dial 121.

After hearing “Enter value”, enter the account number, followed by ”#”.

Example: If the account is “84943122 @ hinet.net”, please enter 0804090403010202714849544560 72544560#.

Please note that it is necessary to enter two digits for each character/number; for example, enter “01” for “1” and “11” for “A”.

PPPoE Password Setting

After entering IVR mode, dial 122 after hearing “enter value” followed by “#”.

Example: If the password is “3ttixike”, please enter “03 60 60 49 64 49 51 45#”.

Save Settings and Restart

To save settings, dial 509 (Save Settings). The system will save the settings. Please restart the system. Wait for about 40 seconds for the system to restart, and then enter 101 to check if the IP address is retained. If the IP address is not repeated, it indicates that Gateway has not been properly connected, please check if the cable connection, account, or password are correct.

Recorded Voice File

The gateway allows users to record their incoming call greeting messages, when calling via FXO.

After entering IVR mode, dial 132. After hearing “Enter value”, record the incoming call greeting message. To end recording, simply hang up.

After recording, to listen to the recorded message, press 131. Press 133 to save the message.

Image 16
Contents DVG-6008S Voip Gateway Page Contents Advanced Feature IP Sharing Functions Coding PrincipleIntroduction Product OverviewHardware Description Front Panel Rear Panel DVG-6008S ModelGateway Assigned with a Public IP Address Network InterfaceGateway in a NAT network Page Telephone Interface Description Integrating Line Ports with PBXPreparation Basic Settings of a GatewayIVR Interactive Voice Response Save Settings Software UpgradesInstructions To inquire about current Gateway’s WAN Port IP addressIVR Functions Table Function Code Description Example Function Code Description Example Static IP Settings Function Command Select a Static IP IP address SettingsSubnet Mask Settings Default Gateway SettingsAdsl PPPoE Settings PPPoE Account SettingsRecorded Voice File Select a PPPoEPPPoE Character Conversion Table Network Settings WAN InstructionsPage IP Configuration Setting WAN Port Setting Dynamic IP DhcpSetting Static IP Adsl PPPoE SettingsBigPond for Australia use only DNS SettingsClone MAC Using Phone Books Manager LAN interface mode※ Network Settings LANLAN IP/Subnet mask Dhcp Settings WAN QoS QoS SettingsLAN QoS※ NAT/DDNS NAT TraversalDdns Telephony Settings Prefix Number RulesExample For exampleHotline Functions Example Description SIP 164 System FXO Representative number registers to Proxy Each line registers to Proxy independentlyCalling Features Advanced Options Line Settings Fax Settings CodecPage Digit Map Phone Book Speed DialCaller Filter CDR SettingsACL for Management Language Transit Call ControlLong-Distance Control Table Long Distance Exception TableCPT/Cadence Settings Busy Tone Cadence MeasurementUDT Detection CPT parameters TableDetailed description is given below Direct Connection to Pstn Connected to a PBX Extension Line Page Save Settings Filling in the CPT TableSystem Information Stun Inquiry RTP Packet SummaryPing Test Backup/Restore SnmpProvision Settings System Operations Save SettingsSoftware Upgrade LogoutIP Sharing Functions Select TCP/IP, and then click Properties Page Instruction Dialed Number Processing FlowEnd Static Route※ RIPRouting Information Protocol ※Port filtering IP FilteringMAC Filtering Virtual ServerURL Filter※ Special Applications※DoS Prevention Settings※