D-Link DVG-6008S user manual Description

Page 31

29

a desired channel, if assigned. If you register to a Proxy it MUST be checked.

Description:

If the remote party wants to assigns L4 (FXO) to make a call, he/she can dial 704 22520199.

If this item isn’t checked, the gateway will select a line automatically to call out from. For example, dial 22520199 without adding the extension number of the FXO port.

Pick up Line by Dialing Extension Number: Allows user to dial just the FXO extension – 703

-to use when the PSTN line is connected on the FXO port. If you are registered to a Proxy, it MUST be checked.

Wait for Caller ID before FXO / Trunk pick up: To detect caller ID from FXO port.

Transit in Busy Tone Limit: The duration gateway plays a busy tone before FXO hook-on. To notify the caller from PSTN that this call is finished.

Ring Time Limit(10 - 600secs)：The timeout to cancel a call when no one answers.

Enable End of Digit Tone：The gateway will play a “Beep-Beep” tone to notify the call is in progress.

VoIP Calling Notification: The gateway will play a tone to notify the call is through VoIP.

Force Calling Thru PSTN code: Dial the code to get a PSTN line for dial out. For example: If you would like dial “23456789” through PSTN and Force Calling Thru PSTN code is *33, just dial “*33 23456789”

Early Media Treatment: If it is disabled, the system will send RTP immediately when the connection with Proxy is set up. The default is enabled. If communicating with other Gateway has problem, please disable this function.

Compare SIP 'To' Header for Transit Out: When FXO is callee and the number of Request line and “To” is different, the system will use the number of “To” to dial out. Please consult your Proxy Server Provider or ITSP about the format of invite packet from Proxy.

Image 31

Contents DVG-6008S Voip Gateway Page Contents IP Sharing Functions Coding Principle Advanced FeatureProduct Overview IntroductionHardware Description Front Panel DVG-6008S Model Rear PanelGateway Assigned with a Public IP Address Network InterfaceGateway in a NAT network Page Integrating Line Ports with PBX Telephone Interface DescriptionPreparation Basic Settings of a GatewayIVR Interactive Voice Response To inquire about current Gateway’s WAN Port IP address Save SettingsSoftware Upgrades InstructionsIVR Functions Table Function Code Description Example Function Code Description Example Default Gateway Settings Static IP Settings Function Command Select a Static IPIP address Settings Subnet Mask SettingsSelect a PPPoE Adsl PPPoE SettingsPPPoE Account Settings Recorded Voice FilePPPoE Character Conversion Table Instructions Network Settings WANPage Adsl PPPoE Settings IP Configuration Setting WAN PortSetting Dynamic IP Dhcp Setting Static IPBigPond for Australia use only DNS SettingsClone MAC Using Phone Books Manager LAN interface mode※ Network Settings LANLAN IP/Subnet mask Dhcp Settings WAN QoS QoS SettingsLAN QoS※ NAT Traversal NAT/DDNSDdns For example Telephony SettingsPrefix Number Rules ExampleHotline Functions Example Description SIP 164 System Each line registers to Proxy independently FXO Representative number registers to ProxyCalling Features Advanced Options Line Settings Codec Fax SettingsPage Digit Map Speed Dial Phone BookCaller Filter CDR SettingsACL for Management Transit Call Control LanguageLong Distance Exception Table Long-Distance Control TableCPT parameters Table CPT/Cadence SettingsBusy Tone Cadence Measurement UDT DetectionDetailed description is given below Direct Connection to Pstn Connected to a PBX Extension Line Page Filling in the CPT Table Save SettingsSystem Information Stun Inquiry RTP Packet SummaryPing Test Snmp Backup/RestoreSystem Operations Save Settings Provision SettingsLogout Software UpgradeIP Sharing Functions Select TCP/IP, and then click Properties Page Dialed Number Processing Flow InstructionEnd RIPRouting Information Protocol ※ Static Route※IP Filtering Port filteringVirtual Server MAC FilteringSpecial Applications※ URL Filter※DoS Prevention Settings※