3Com 4210G manual LEDs, Combo Port, Model SFP port 10/100/1000Base-T Ethernet port, Device support

Page 17

Combo Port

One SFP port and the corresponding 10/100/1000Base-T Ethernet port form a Combo port. For each Combo port, either the SFP port or the corresponding 10/100/1000Base-T Ethernet port can be used at a time. For details about the combo port mapping relationship, please refer to Table 1-4.

Table 1-4Combo port mapping relationship

 

Model

SFP port

10/100/1000Base-T Ethernet port

 

 

 

 

GigabitEthernet1/0/25

GigabitEthernet1/0/22

 

 

Switch 4210G 24-Port

 

 

 

 

GigabitEthernet1/0/26

GigabitEthernet1/0/24

 

 

Switch 4210G NT 24-Port

 

 

 

 

 

 

GigabitEthernet1/0/27

GigabitEthernet1/0/21

 

 

Switch 4210G

PWR 24-Port

 

 

 

 

 

 

 

 

GigabitEthernet1/0/28

GigabitEthernet1/0/23

 

 

 

 

 

 

 

 

 

 

GigabitEthernet1/0/49

GigabitEthernet1/0/46

 

 

Switch 4210G

48-Port

 

 

 

 

GigabitEthernet1/0/50

GigabitEthernet1/0/48

 

 

Switch 4210G

NT 48-Port

 

 

 

 

 

 

GigabitEthernet1/0/51

GigabitEthernet1/0/45

 

 

Switch 4210G

PWR 48-Port

 

 

 

 

 

 

 

 

GigabitEthernet1/0/52

GigabitEthernet1/0/47

 

 

 

 

 

 

 

 

 

 

 

 

 

The SFP port and its corresponding 10/100/1000Base-T autosensing Ethernet port cannot be used together at the same time. For details, refer to the Ethernet Port Configuration part in the Access Volume of the 3Com Switch 4210G Family Configuration Guide.

LEDs

Table 1-5 LEDs

LED

Device support

System Status LED

All series

 

 

RPS Status LED

All series

 

 

Port Mode LED

All series

 

 

Seven-Segment LED

All series

 

 

10/100/1000Base-TAuto-Sensing

All series

Ethernet Port Status LED

 

 

 

1000Base-X SFP Port Status LED

All series

 

 

Interface Module Status LED

Switch 4210G 24-Port, Switch 4210G 48-Port, Switch

4210G PWR 24-Port, and Switch 4210G PWR 48-Port

 

 

 

1-10

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 3Com Switch 4210G Family Environmental Statement About This Manual Chapter ContentsOrganization ConventionsObtaining Documentation Related DocumentationCreate Folder Convention DescriptionTable of Contents Page Iii 4210G 24-Port 4210G 48-Port 4210G PWR 4210G NT OverviewVDC Switch 4210G 24-Port Introduction to Switch 4210GSwitch 4210G 48-Port Switch 4210G PWR 24-Port Switch 4210G PWR 48-Port Switch 4210G NT 24-Port Console Port Switch 4210G NT 48-PortPorts 1000Base-X SFP Port Specification10/100/1000Base-T Ethernet Port Combo Port LEDsModel SFP port 10/100/1000Base-T Ethernet port LEDsSystem Status LED Port Mode LEDRPS Status LED Status DescriptionSystem status Seven-segment LED Description Seven-Segment LEDStatus 10/100/1000Base-T Auto-Sensing Ethernet Port Status LED 1000Base-X SFP Port Status LED Status Description Port mode Ethernet portInterface Module Status LED Optional Interface ModulesShort-haul Dual-Port 10 GE CX4 Interface Module Mark Status DescriptionDual-Port 10 GE XFP Interface Module CX4 Cable Connector type LengthDistance Central Max Transceiver Connector Fiber TransmissionOne-port 10 GE XFP Interface Module Transceiver Central Max Connector Fiber Transmission Cable type DistanceDual-Port 10 GE SFP+ Interface Module 22 SFP+ cable Description of LEDs of Interface ModulesInstallation Site Safety PrecautionsCleanness Temperature/HumidityElectromagnetic Susceptibility Gas Maximum concentration mg/mLaser Safety Installation ToolsInstallation Flow of the Switch Installing the SwitchIntroduction to Mounting Bracket Model Physical dimensions × W × D Use Front Mounting Brackets to Install a SwitchConfiguration Type of front Mounting bracket Configuration Type of rear Mounting BracketUse Front Mounting Brackets and a Tray to Install a Switch Use Front and Rear Mounting Brackets to Install a Switch Page Page Mounting the Switch on a Workbench When a Grounding Strip is Available Connecting the Grounding CableWhere a Grounding Conductor Can be Buried Other Installation Sites Switch module Power supply Connection method Mode Connecting the Power CordsConnecting the AC Power Cord 16Connect an AC power cord to a horizontal AC power socket Connecting the RPS Power CordPage Installing an Interface Card Installing an Interface ModuleRemoving an Interface Module Installing Dedicated CX4/SFP+ CableRemoving Dedicated CX4/SFP+ Cable Installing Switches for an IRFTask Remarks Installation Flow for an IRFFor details, see Installing an Interface Module Drawing a Plan for an IRF with SwitchesConfigure the physical connection mode Page 29Cable connections for an IRF with 1-port interface modules Verifying the InstallationConnecting the Console Cable Setting up the Configuration EnvironmentRJ-45 Signal Direction DB-9 Console CableConnection Procedure Setting Terminal Parameters4Set the serial port used by the HyperTerminal connection 6HyperTerminal window Powering on the Switch Booting the SwitchChecking before Powering on the Switch Describes the fields above 2Description on the fields Changing the Startup Mode Enter Y. The system displays the following information BUS Clock Speed 33MHz Memory Size 128MB Mac Address Page Introduction to Loading Modes Loading Software Through the Boot ROM MenuBoot Menu Press Ctrl + B. The system displays Introduction to Xmodem Loading Software Using Xmodem Through Console PortROM file effective Required2Properties dialog box Cccccccccccccccccc CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCdone Loading host software Loading Software Using Tftp through Ethernet PortLoad File name Introduction to FTP Loading Software Using FTP Through Ethernet PortDescription Loading Software Through CLI Loading Software Using FTPUpdate the Boot ROM program on the switch Loading Software Using TftpMissing User Password Password Missing FailureMissing Boot ROM Password Software Loading FailureAC input Power Supply FailureRPS input RPS&AC inputSteady red Fan FailureMark State System status LED Troubleshooting when the terminal display is illegible Configuration System FailureTroubleshooting when there is no terminal display
Top Page Image Contents