Wacom manual DTU-710 Component Functions, Front View

Page 16

DTU-710 Component Functions

Front View

MENU Button

Opens and closes the OSD*1 menu.

- (minus) Button, + (plus) Button

In the OSD*1 menu, Use these buttons to select an option that can then be activated. After activating a selected option, press the + button to increase a selected item value, and press the - button to decrease it.

 

-

NE

 

 

 

 

 

 

 

MENU

ENTER STATUS POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Integrated Tablet and LCD Screen

The LCD monitor*2 and tablet sensor function*3 as an integrated input and output device.

The LCD resolution is 1280 x 1024 pixels at 16,194,277 colors. The tablet sensor reports coordinates, pressure, switch, and eraser information.

ENTER Button

Press this button when you select or exit an item in the OSD*1 menu. P 22

POWER Switch

Turns the power to the unit on or off.

POWER Lamp

Lights blue when power has been supplied to both the DTU-710 and the computer and a video signal is present.

Glows orange when no video signal is received by the DTU-710. (e.g., Your computer is turned off, starting up, or has entered a power management mode in which video signals are not sent.)

STATUS Lamp

Lights blue when the pen is in the active area of the pen display tablet and the pen tip, side switch, or eraser are pressed. Note that the USB cable must be plugged into an active USB port before the LED will light.

*1 On Screen Display. P. 22

*2 As properties of LCD panel display, you may notice the followings. They do not mean the LCD is defective.

-When exerting hard downward pressure on the display, a moir pattern may temporarily appear.

-A very small number of pixels may appear in incorrect color.

-If an image area has fine striping (such as screen stripes), it may flicker or display a moir pattern or pooling image.

-When a still image is displayed for a long period of time, an afterimage may remain for a short period

of time.

*3 As the tablet portion of DTU-710 emits electromagnetic waves at a certain frequency, if another tablet is closely placed to DTU-710, the screen cursor may jitters or jumps around. To solve this problem, place the tablet away from DTU-710.

16

Image 16
Contents Introduction and Overview Precautions on Use and Handling Page Table of Contents Checking Packed Components Connect DTU-710 to a computer Connect DTU-710 to a computer as adisplayConnect one cable onl y To serial port Tablet Driver Installation WindowsUninstalling The DTU-710 Windows XPCustomizing The DTU-710 The Basics Opening the Wacom Tablet Control PanelControl Panel Basics Customizing The PenControl Panel Details Side switchPen Tip Feel & Eraser Feel Modifier Calibrating the DTU-710 Cross-hairsPage DTU-710 Component Functions Front ViewStand Adjustment Lever Connector Panel CoverRear View StandUsing an Alternate Mount or Stand Using the Pen Side Switch and Second Side SwitchPen Pen TipUsing a Pen Removing the Side SwitchTo reinstall the side switch, reverse the above procedure Adjusting the LCD Monitor Factory Presets, Multi-sync, and User SettingsContrast Phase VGA only Working with OSD On Screen Display MenuVertical Center Reset Horizontal CenterVGA only Menu PositionColor BacklightAdjusting Pitch and Phase VGA only Power Saving HintCaring for DTU-710 CleaningReplacing the Pen Tip Display Troubleshooting TroubleshootingGeneral Display Problems Troubleshooting VGA ProblemsPen Tablet Troubleshooting General ProblemsTroubleshooting Windows\System32 folder. Then restart your computer. When Windows-Specific Problems Macintosh-Specific Problems Specifications General SpecificationsPower Adaptor Support Staff Obtaining Technical SupportAsia Trademarks