Wacom manual Connect DTU-710 to a computer as adisplay

Page 6

Connect DTU-710 to a computer

Connect DTU-710 to a computer as adisplay.

CAUTION

■Do not use any cable that did not come with DTU-710; use of an improper cable may damage DTU-710.

■Make sure your graphics card has a VGA or DVI connector, and that you correctly set the DTU-710 Analog (VGA)/Digital (DVI) switch for the graphics card you are using. The use of an improper video card may damage DTU-710.

■Do not connect or disconnect the video or power cable while DTU-710 or your computer are turned on; this can damage the LCD display or computer video card.

■Never connect or disconnect the DVI video cable or power cable while your computer or DTU-710 is powered on. This can damage the LCD display or video card.

1.Turn off your computer. The cover in the rear of DTU-710 is made to slide in the direction of " ▶ ", and is removed.

2.Connect the DVI-to-DVI cable or DVI-to-VGA cable between DTU-710 and your computer.

3.Set the DVI/VGA switch. Move it up for analog (VGA) mode, and move it down for digital (DVI) mode.

4.Connect the AC adaptor to DTU-710.

5.Connect the AC adaptor power cable and plug the adaptor into an AC outlet. Be sure to connect an earth cable.

6.Turn on the power switch of DTU-710. The power lamp will light blue, and then turns orange.

7.Turn on your computer to start your operating system.

8.The maximum resolution of DTU-710 is 1280 x 1024, True Color . As necessary, configure the monitor control panel settings for the proper size and color resolution.

The number of colors is constrained by the performance of your computer or graphics card. Refer to the documentation of the manufacturer for details.

If you are using analog (VGA) mode, you may also want to fine-tune the display. Please refer to Adjusting the LCD Monitor on page 22 for more information.

9.To install the Wacom tablet software, turn off your computer and connect the USB cable or serial data cable.

10.Fix cables to a cable guides. Shut the connector cover is and take out the cables from the hole of the cover.

11.Install tablet software. Refer to Tablet Software Installation for Windows and Macintosh on page 8.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Introduction and Overview Precautions on Use and Handling Page Table of Contents Checking Packed Components Connect DTU-710 to a computer Connect DTU-710 to a computer as adisplayConnect one cable onl y To serial port Tablet Driver Installation WindowsUninstalling The DTU-710 Windows XPCustomizing The DTU-710 The Basics Opening the Wacom Tablet Control PanelControl Panel Basics Customizing The PenSide switch Control Panel DetailsPen Tip Feel & Eraser Feel Modifier Calibrating the DTU-710 Cross-hairsPage DTU-710 Component Functions Front ViewRear View Stand Adjustment LeverConnector Panel Cover StandUsing an Alternate Mount or Stand Pen Using the PenSide Switch and Second Side Switch Pen TipUsing a Pen Removing the Side SwitchTo reinstall the side switch, reverse the above procedure Contrast Phase VGA only Adjusting the LCD MonitorFactory Presets, Multi-sync, and User Settings Working with OSD On Screen Display MenuColor Vertical Center ResetHorizontal CenterVGA only Menu Position BacklightAdjusting Pitch and Phase VGA only Power Saving HintCleaning Caring for DTU-710Replacing the Pen Tip Troubleshooting Display TroubleshootingGeneral Display Problems Troubleshooting VGA ProblemsPen Tablet Troubleshooting General ProblemsTroubleshooting Windows\System32 folder. Then restart your computer. When Windows-Specific Problems Macintosh-Specific Problems Specifications General SpecificationsPower Adaptor Obtaining Technical Support Support StaffAsia Trademarks
Top Page Image Contents