Datalogic Scanning DS2200 SH2348 manual Symbologies, Code Interleaved 2 Standard 2 Codabar

Page 18

Symbologies

The bar codes that can be read by PSC’s bar code scanners include:

Code 39	Code 93
Interleaved 2 of 5	Code 128
Standard 2 of 5	Codabar
UPC-A, UPC-E	Code 11
EAN/JAN	MSI/Plessey

A complete list of the related options and the instructions for setting them are provided in the section on Symbologies.

		Scanning problems are most often caused by poor quality
		bar code symbols. If scanning problems arise, test your bar
		code system using the high quality bar code test symbols
	NOTE	supplied in this manual or contact your PSC Customer Ser-
	NOTE	vice representative.
		vice representative.

10	User’s / Programming Guide

Image 18

Contents User’s / Programming Guide PSC Inc DisclaimerPage Page Table of Contents Message Formatting Serial CommandsKeyboard Wedge Parameters Symbologies Wand Emulation ParametersScanner Labeling IiiMemory Module Technical SupportUser’s / Programming Guide Introduction Unpacking InstallationCable Installation Keyboard WedgeTerminal Power-Up Sequence Connecting the Power SupplyConnecting a Magnetic Stripe Reader Scanning Reset to Default ZA will cause the PSC scanSerial TTL Mode Serial RS232 ModeSerial Communications AutoSense Operation Enable AutoSense Disable AutoSense Scanner holder Stand baseSame Code Wand Emulation Enable Wedge Enable Serial ModeWand Emulation Operation Code Type = Same Code Wand EmulationSetup Overview Wedge Mode OptionsWand Emulation Options Baud Rate Protocol Parity Serial Communication and Wedge OptionsData Synchronization Stop BitsCode SymbologiesCode Interleaved 2 Standard 2 Codabar Vice representativeBeeper On Volume Low Parameters Selection GuidelinesExamples User’s / Programming Guide Baud Rate Reset DefaultSerial Communication Select Serial OutputData Transmission Bit Options Data Stop Bits ParityOdd Even Mark Space Mark Space None Bit, No ParityCommunications Protocol Inverted Serial CommunicationsCTS Disable Stop/Go Protocol Enable Stop/Go Protocol No Read Option Enable No Read Disable No ReadLabel Buffering Full Buffering No Buffering One Label BufferingDisable External Trigger#*@ External Trigger+ Menu Commands Parameter MessagesEnable Parameter Messages Disable Parameter Messages External Trigger OperationGeneral Parameters Intercharacter DelayNo interlabel delay *@ Set interlabel delay 0-9.9 seconds External TriggerTransmission Mode System StatusEnable Continuous@ Full Power Enable Standby *# Power ConsumptionDisplay Configuration Laser RedundancyBeeper Off Beeper On Volume Low Laser TimeoutEnable 4 Times Laser Redundancy Beeper OperationPrefixes and Suffixes Beeper On Volume Medium Beeper On Volume Loud *#@Message Formatting Programmable options do not apply in Wand Emu LationPrefix SuffixPrefix = None*# Prefix = STX Prefix = SOH Suffix = CR and LF Terminal ID Select Suffix = ETB NULCode Identifier Code Identifier CharactersPostamble Preamble or Postamble SelectionPreamble 0,0 hexadecimalUser’s / Programming Guide Serial Commands General Serial Command FormatCommand Function Enable I 2 of 5 with check digitBeeper Off CR-LF Ack Power Standby and Serial Commands Communication Parameter ChangesManual Scanning Interaction Wedge Mode Enable @ Keyboard Wedge Parameters06656 User’s / Programming Guide Explained in Appendix a Symbologies Disable UPC both a and EUPC a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Enable transmissionof UPC-E check digit Disable UPC-EDisable EAN/JAN 8 or 13 Digit #@ EAN/JANDisable EAN-8 independently Disable Code CodeFollowing are only valid if CHK Char is enabled Do Not Xmit Start and STOP*#@ Transmit Start and StopDisable Interleaved Code 2 of 5*#@ Code 2 of 5 InterleavedMaximum Length I 2 of 5 specified by two digits Code 2 of 5 Standard Enable Codabar Enable Code 128 *#@Disable Codabar *#@ Minimum Length specified by two digitsEnable Transmission of START/ Stop Character Maximum Length specified by two digitsMSI/Plessey Enable Code Standard Code Enable 16K Code Disable 16K Code 16KDigit Selection Symbology Identifiers Symbol Function06656 Programming Symbol Bology identifiersStandard 2/5 Code Symbology IdentifiersEAN-13 Code MSI/PlesseyBar Code Polarity Wand Emulation ParametersSelect Code Type Transmission RateInches per second# Disable Data # Synchronization Enable Data Synchronization Data SynchronizationActive # Polarity High Active Polarity Low Memory Module Setup Disable Memory Module*# Enable Memory ModuleEnable Marker Beam Disable Marker Beam Marker Beam06656 Service and Warranty Scanner LabelingHazardous visible light exposure Maintenance CleaningInspection Reseller Technical Support Technical SupportPSC Website Support PSC Website TekForum Telephone Technical SupportAppendix a Hexadecimal Conversion TablePart a Part B Primary Function Key Table Ascii HEX FunctionSecondary Function Key Tables PC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25IBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc