Datalogic Scanning DS2200 SH2348, DS1100 SH2347 manual IBM 3171/3181/3191 and IBM

Page 82

Secondary Function Key Tables

IBM 3171/3181/3191 and IBM 3477

ASCII

HEX

FUNCTION

NUL

00

ESCAPE

SOH

01

ON LINE ENTER (Make/Break)

STX

02

ALT left side Make

ETX

03

ALT left side Break

EOT

04

ON LINE ENTER (Make only)

ENQ

05

FIELD EXIT (Make only)

ACK

06

ENTER right keypad

BEL

07

Cursor up (inner keypad)

BS

08

Cursor dn (inner keypad)

HT

09

Cursor left (inner keypad)

LF

0A

Cursor right (inner keypad)

VT

0B

TAB FWD

FF

0C

DEL (inner keypad)

CR

0D

FIELD EXIT (Make/Break)

SO

0E

INS (inner keypad)

SI

0F

Page Up (inner keypad)

DLE

10

Page Dn (inner keypad)

DC1

11

HOME (inner keypad)

DC2

12

PRINT SCREEN

DC3

13

BACKSPACE

DC4

14

BACKFIELD (Shift TAB)

NAK

15

SCROLL LOCK

SYN

16

F1

ETB

17

F2

CAN

18

F3

EM

19

F4

SUB

1A

F5

ESC

1B

F6

FS

1C

F7

GS

1D

F8

RS

1E

F9

US

1F

F10

74

User’s / Programming Guide

Image 82
Contents User’s / Programming Guide PSC Inc DisclaimerPage Page Table of Contents Message Formatting Serial CommandsKeyboard Wedge Parameters Symbologies Wand Emulation ParametersScanner Labeling IiiMemory Module Technical SupportUser’s / Programming Guide Introduction Unpacking InstallationCable Installation Keyboard WedgeTerminal Power-Up Sequence Connecting the Power SupplyConnecting a Magnetic Stripe Reader Scanning Reset to Default ZA will cause the PSC scanSerial RS232 Mode Serial TTL ModeSerial Communications AutoSense Operation Enable AutoSense Disable AutoSense Scanner holder Stand baseSame Code Wand Emulation Enable Wedge Enable Serial ModeWand Emulation Operation Code Type = Same Code Wand EmulationWedge Mode Options Setup OverviewWand Emulation Options Baud Rate Protocol Parity Serial Communication and Wedge OptionsData Synchronization Stop BitsCode SymbologiesCode Interleaved 2 Standard 2 Codabar Vice representativeParameters Selection Guidelines Beeper On Volume LowExamples User’s / Programming Guide Baud Rate Reset DefaultSerial Communication Select Serial OutputBit Options Data Stop Bits Parity Data TransmissionOdd Even Mark Space Mark Space None Bit, No ParityCommunications Protocol Inverted Serial CommunicationsCTS Disable Stop/Go Protocol Enable Stop/Go Protocol No Read Option Enable No Read Disable No ReadLabel Buffering Full Buffering No Buffering One Label BufferingDisable External Trigger#*@ External Trigger+ Menu Commands Parameter MessagesEnable Parameter Messages Disable Parameter Messages External Trigger OperationGeneral Parameters Intercharacter DelayNo interlabel delay *@ Set interlabel delay 0-9.9 seconds External TriggerTransmission Mode System StatusEnable Continuous@ Full Power Enable Standby *# Power ConsumptionDisplay Configuration Laser RedundancyBeeper Off Beeper On Volume Low Laser TimeoutEnable 4 Times Laser Redundancy Beeper OperationPrefixes and Suffixes Beeper On Volume Medium Beeper On Volume Loud *#@Message Formatting Programmable options do not apply in Wand Emu LationSuffix PrefixPrefix = None*# Prefix = STX Prefix = SOH Suffix = CR and LF Terminal ID Select Suffix = ETB NULCode Identifier Code Identifier CharactersPostamble Preamble or Postamble SelectionPreamble 0,0 hexadecimalUser’s / Programming Guide Serial Commands General Serial Command FormatEnable I 2 of 5 with check digit Command FunctionBeeper Off CR-LF Ack Communication Parameter Changes Power Standby and Serial CommandsManual Scanning Interaction Wedge Mode Enable @ Keyboard Wedge Parameters06656 User’s / Programming Guide Explained in Appendix a Disable UPC both a and E SymbologiesUPC a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Enable transmissionof UPC-E check digit Disable UPC-EDisable EAN/JAN 8 or 13 Digit #@ EAN/JANDisable EAN-8 independently Disable Code CodeFollowing are only valid if CHK Char is enabled Do Not Xmit Start and STOP*#@ Transmit Start and StopCode 2 of 5 Interleaved Disable Interleaved Code 2 of 5*#@Maximum Length I 2 of 5 specified by two digits Code 2 of 5 Standard Enable Codabar Enable Code 128 *#@Disable Codabar *#@ Minimum Length specified by two digitsEnable Transmission of START/ Stop Character Maximum Length specified by two digitsMSI/Plessey Enable Code Standard Code Enable 16K Code Disable 16K Code 16KDigit Selection Symbology Identifiers Symbol Function06656 Programming Symbol Bology identifiersStandard 2/5 Code Symbology IdentifiersEAN-13 Code MSI/PlesseyBar Code Polarity Wand Emulation ParametersSelect Code Type Transmission RateInches per second# Disable Data # Synchronization Enable Data Synchronization Data SynchronizationActive # Polarity High Active Polarity Low Memory Module Setup Disable Memory Module*# Enable Memory ModuleEnable Marker Beam Disable Marker Beam Marker Beam06656 Scanner Labeling Service and WarrantyHazardous visible light exposure Cleaning MaintenanceInspection Reseller Technical Support Technical SupportPSC Website Support PSC Website TekForum Telephone Technical SupportAppendix a Hexadecimal Conversion TablePart a Part B Primary Function Key Table Ascii HEX FunctionSecondary Function Key Tables PC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25IBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc