Datalogic Scanning DS1100 SH2347, DS2200 SH2348 Disable Expanded UPC-E *#@ Enable Expanded UPC-E

Page 47

Option QB or Option QC enable both UPC-A and UPC-E. If UPC is enabled, any UPC label, with or without supplement, is read. The supplement is read if Option QB is selected, and it is ignored if Option QC is selected.

QB

QC

Enable UPC with 2 or 5 Digit Supplement Enabled

Enable UPC with 2 or 5 Digit Supplement Disabled *#@

Expanded UPC-E is disabled by scanning Option QH, or is enabled by scanning Option QI.

QH

Disable Expanded UPC-E *#@

QI

Enable Expanded UPC-E

Transmission of the first character in a UPC symbol (the number sys- tem character) is disabled by scanning Option QD or enabled by scanning Option QE.

QD

QE

Disable Transmission of Number System Digit

Enable Transmission of Number System Digit *#@

06656

39

Image 47

Contents User’s / Programming Guide Disclaimer PSC IncPage Page Table of Contents Wand Emulation Parameters Serial CommandsKeyboard Wedge Parameters Symbologies Message FormattingTechnical Support IiiMemory Module Scanner LabelingUser’s / Programming Guide Introduction Keyboard Wedge InstallationCable Installation UnpackingScanning Reset to Default ZA will cause the PSC scan Connecting the Power SupplyConnecting a Magnetic Stripe Reader Terminal Power-Up SequenceSerial Communications Serial TTL ModeSerial RS232 Mode AutoSense Operation Scanner holder Stand base Enable AutoSense Disable AutoSenseCode Type = Same Code Wand Emulation Enable Wedge Enable Serial ModeWand Emulation Operation Same Code Wand EmulationWand Emulation Options Setup OverviewWedge Mode Options Stop Bits Serial Communication and Wedge OptionsData Synchronization Baud Rate Protocol ParityVice representative SymbologiesCode Interleaved 2 Standard 2 Codabar CodeExamples Beeper On Volume LowParameters Selection Guidelines User’s / Programming Guide Select Serial Output Reset DefaultSerial Communication Baud RateOdd Even Mark Space Data TransmissionBit Options Data Stop Bits Parity Mark Space Inverted Serial Communications Bit, No ParityCommunications Protocol NoneCTS Disable Stop/Go Protocol Enable Stop/Go Protocol Full Buffering No Buffering One Label Buffering Enable No Read Disable No ReadLabel Buffering No Read OptionExternal Trigger Operation Menu Commands Parameter MessagesEnable Parameter Messages Disable Parameter Messages Disable External Trigger#*@ External Trigger+External Trigger Intercharacter DelayNo interlabel delay *@ Set interlabel delay 0-9.9 seconds General ParametersSystem Status Transmission ModeLaser Redundancy Power ConsumptionDisplay Configuration Enable Continuous@ Full Power Enable Standby *#Beeper Operation Laser TimeoutEnable 4 Times Laser Redundancy Beeper Off Beeper On Volume LowProgrammable options do not apply in Wand Emu Lation Beeper On Volume Medium Beeper On Volume Loud *#@Message Formatting Prefixes and SuffixesPrefix = None*# Prefix = STX Prefix = SOH PrefixSuffix Terminal ID Select Suffix = ETB NUL Suffix = CR and LFCode Identifier Characters Code Identifier0,0 hexadecimal Preamble or Postamble SelectionPreamble PostambleUser’s / Programming Guide General Serial Command Format Serial CommandsBeeper Off CR-LF Ack Command FunctionEnable I 2 of 5 with check digit Manual Scanning Interaction Power Standby and Serial CommandsCommunication Parameter Changes Keyboard Wedge Parameters Wedge Mode Enable @06656 User’s / Programming Guide Explained in Appendix a UPC a and E SymbologiesDisable UPC both a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Disable UPC-E Enable transmissionof UPC-E check digitEAN/JAN Disable EAN/JAN 8 or 13 Digit #@Disable EAN-8 independently Code Disable CodeDo Not Xmit Start and STOP*#@ Transmit Start and Stop Following are only valid if CHK Char is enabledMaximum Length I 2 of 5 specified by two digits Disable Interleaved Code 2 of 5*#@Code 2 of 5 Interleaved Code 2 of 5 Standard Minimum Length specified by two digits Enable Code 128 *#@Disable Codabar *#@ Enable CodabarMaximum Length specified by two digits Enable Transmission of START/ Stop CharacterMSI/Plessey Enable Code Standard Code 16K Enable 16K Code Disable 16K CodeDigit Selection Symbol Function Symbology Identifiers06656 Bology identifiers Programming SymbolMSI/Plessey Symbology IdentifiersEAN-13 Code Standard 2/5 CodeTransmission Rate Wand Emulation ParametersSelect Code Type Bar Code PolarityInches per second# Data Synchronization Disable Data # Synchronization Enable Data SynchronizationActive # Polarity High Active Polarity Low Memory Module Disable Memory Module*# Enable Memory Module SetupMarker Beam Enable Marker Beam Disable Marker Beam06656 Hazardous visible light exposure Service and WarrantyScanner Labeling Inspection MaintenanceCleaning Telephone Technical Support Technical SupportPSC Website Support PSC Website TekForum Reseller Technical SupportHexadecimal Conversion Table Appendix aPart a Part B Ascii HEX Function Primary Function Key TablePC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25 Secondary Function Key TablesIBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc