Datalogic Scanning DS2200 SH2348, DS1100 SH2347 manual Ean/Jan, Disable EAN/JAN 8 or 13 Digit #@

Page 50

EAN/JAN

Scan Option RA to disable EAN/JAN (8 or 13 digit).

RA

Disable EAN/JAN (8 or 13 Digit) #@

Option RB or RC enables both EAN 8 digit and EAN 13 digit. If EAN/JAN is enabled, any EAN/JAN label, with or without supple- ment, is read. The supplement is read if Option RB is selected and is ignored if Option RC is selected.

RB

RC

Enable EAN/JAN with 2 or 5 Digit Supplement enabled

Enable EAN/JAN with 2 or 5 Digit *Supplement disabled

Transmission of the first character in an EAN/JAN symbol (the num- ber system character) is disabled by scanning Option RD, or is enabled by scanning Option RE.

RD

RE

Disable Transmission of Number System Digit

Enable Transmission of Number System Digit *#@

42

User’s / Programming Guide

Image 50
Contents User’s / Programming Guide PSC Inc DisclaimerPage Page Table of Contents Message Formatting Serial CommandsKeyboard Wedge Parameters Symbologies Wand Emulation ParametersScanner Labeling IiiMemory Module Technical SupportUser’s / Programming Guide Introduction Unpacking InstallationCable Installation Keyboard WedgeTerminal Power-Up Sequence Connecting the Power SupplyConnecting a Magnetic Stripe Reader Scanning Reset to Default ZA will cause the PSC scanSerial Communications Serial TTL ModeSerial RS232 Mode AutoSense Operation Enable AutoSense Disable AutoSense Scanner holder Stand baseSame Code Wand Emulation Enable Wedge Enable Serial ModeWand Emulation Operation Code Type = Same Code Wand EmulationWand Emulation Options Setup OverviewWedge Mode Options Baud Rate Protocol Parity Serial Communication and Wedge OptionsData Synchronization Stop BitsCode SymbologiesCode Interleaved 2 Standard 2 Codabar Vice representativeExamples Beeper On Volume LowParameters Selection Guidelines User’s / Programming Guide Baud Rate Reset DefaultSerial Communication Select Serial OutputOdd Even Mark Space Data TransmissionBit Options Data Stop Bits Parity Mark Space None Bit, No ParityCommunications Protocol Inverted Serial CommunicationsCTS Disable Stop/Go Protocol Enable Stop/Go Protocol No Read Option Enable No Read Disable No ReadLabel Buffering Full Buffering No Buffering One Label BufferingDisable External Trigger#*@ External Trigger+ Menu Commands Parameter MessagesEnable Parameter Messages Disable Parameter Messages External Trigger OperationGeneral Parameters Intercharacter DelayNo interlabel delay *@ Set interlabel delay 0-9.9 seconds External TriggerTransmission Mode System StatusEnable Continuous@ Full Power Enable Standby *# Power ConsumptionDisplay Configuration Laser RedundancyBeeper Off Beeper On Volume Low Laser TimeoutEnable 4 Times Laser Redundancy Beeper OperationPrefixes and Suffixes Beeper On Volume Medium Beeper On Volume Loud *#@Message Formatting Programmable options do not apply in Wand Emu LationPrefix = None*# Prefix = STX Prefix = SOH PrefixSuffix Suffix = CR and LF Terminal ID Select Suffix = ETB NULCode Identifier Code Identifier CharactersPostamble Preamble or Postamble SelectionPreamble 0,0 hexadecimalUser’s / Programming Guide Serial Commands General Serial Command FormatBeeper Off CR-LF Ack Command FunctionEnable I 2 of 5 with check digit Manual Scanning Interaction Power Standby and Serial CommandsCommunication Parameter Changes Wedge Mode Enable @ Keyboard Wedge Parameters06656 User’s / Programming Guide Explained in Appendix a UPC a and E SymbologiesDisable UPC both a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Enable transmissionof UPC-E check digit Disable UPC-EDisable EAN/JAN 8 or 13 Digit #@ EAN/JANDisable EAN-8 independently Disable Code CodeFollowing are only valid if CHK Char is enabled Do Not Xmit Start and STOP*#@ Transmit Start and StopMaximum Length I 2 of 5 specified by two digits Disable Interleaved Code 2 of 5*#@Code 2 of 5 Interleaved Code 2 of 5 Standard Enable Codabar Enable Code 128 *#@Disable Codabar *#@ Minimum Length specified by two digitsEnable Transmission of START/ Stop Character Maximum Length specified by two digitsMSI/Plessey Enable Code Standard Code Enable 16K Code Disable 16K Code 16KDigit Selection Symbology Identifiers Symbol Function06656 Programming Symbol Bology identifiersStandard 2/5 Code Symbology IdentifiersEAN-13 Code MSI/PlesseyBar Code Polarity Wand Emulation ParametersSelect Code Type Transmission RateInches per second# Disable Data # Synchronization Enable Data Synchronization Data SynchronizationActive # Polarity High Active Polarity Low Memory Module Setup Disable Memory Module*# Enable Memory ModuleEnable Marker Beam Disable Marker Beam Marker Beam06656 Hazardous visible light exposure Service and WarrantyScanner Labeling Inspection MaintenanceCleaning Reseller Technical Support Technical SupportPSC Website Support PSC Website TekForum Telephone Technical SupportAppendix a Hexadecimal Conversion TablePart a Part B Primary Function Key Table Ascii HEX FunctionSecondary Function Key Tables PC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25IBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc