Yamaha DPX-1300 manual Loading the batteries into the remote control

Page 12

◆Loading the batteries into the remote control

1.Remove the battery compartment cover.

2.Insert two batteries (AA, UM3, or R6 type), matching the polarity markings on the batteries with those in the battery compartment.

3.After loading the batteries, close the cover until it snaps into

place.

1 3

2

Warning

•If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the batteries for new ones.

•Do not mix old and new, or different types of batteries.

•Remove the batteries if you do not plan to use the unit for a long time.

•If the batteries leak, dispose of them immediately, taking care not to touch the battery fluid. If the battery fluid comes into contact with your eyes, mouth, or skin, rinse it off with water immediately and consult a doctor. Clean the battery compartment thoroughly before installing new batteries.

◆Using the remote control with a wired connection

Use a 2P monaural miniplug cable (commercially available) to connect the remote control jack on the underside of the remote control to the REMOTE IN jack on the main unit. Use the wired remote control configuration to control the DPX-1300 without having to be within range of the remote sensor.

4

INPUT

1	2 INPUT
	2 INPUT
5	3

-1 ID

-2 ID

INPUT

LIGH

T

6

8

Image 12

Contents DPX-1300 Important Safety Instructions We Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Features EnglishMain unit Front panel and controls Main unit Rear panel / Connections Controls and functionsRemote control functions Remote control English Light switchRemote control code switch Remote control cable jackLoading the batteries into the remote control Using the remote control with a wired connectionLimits for using the remote control Distance to sensor Angle to sensorUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationTurn the power on and selecting an image for projection PrepararionSetting up the DPX-1300 Mounting the projector on a tableMounting the projector on the ceiling Installation When using a 169 screenWhen using a 43 screen Projection distanceKeystone adjustment Using Zoom to adjust image positionUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionConnecting to AV components ConnectionConnecting to computer devices Information for installersFor US model only + polarity inside Polarity outside GNDChecking installation and connections Pre-operation checkProjection English Projection preparations completeTurning the projector power on Turning the power onPress the STANDBY/ON button Button on the remote control Placing the DPX-1300 in standby mode Lamp may blink when half lit. This is not a defectPress the STANDBY/ON button Selecting an input signal Selecting using the Input buttonProjection image signal Using the Input button to select a signal ProjectionPress the + button to open the submenu Selecting a display aspect for a projection image Press the Aspect buttonRemote cotrol Display aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesAdjusting the image Adjusting the vertical position V.POS buttonPattern button Crosshatch pattern Grayscale pattern Color bar patternAdjusting the size of an image Zoom button Menu configurations Menu screenMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Menu Level Adjustment Adjusts the iris OpticalAdjusts the analog input signal gain and offset settings White PeakingSignal Menu EnglishSignal Level Signal StatusOvershoot Supp. Range Overshoot Supp. LevelInitial Setup Menu Color MessageTrigger Out Baud RateReset button Remote control only Remote ControlMenu operations Operation button functionsMenu operations 1 with no submenu Press the Menu button to openMenu screen Press the + or button to select a menu groupPress the + or button to select a suitable setting Setting method depends on the item selectedRemote Control Main Unit Menu Button Remote Control Main UnitPress the h or g button to adjust item settings Menu operations 2 with submenusPress the + button to move to the submenu Appears to the right of items that contain a submenuSpecial operations See page 32 for datails about each color itemExample Using the color temperature fixed mode Example Color temperature fixed modeName of the selected item appears here Resetting the selected settings Resetting all the settingsChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonAdjusting image quality using the inline menu Example Using the inline menuInline menu composition Inline menu item listMemory configurations Saving memory settingsUsing the remote control Using the menuMemory function English Press the g button to select Memory number status fromBottom of the screen Press the h or g button to select a memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Select the memory number youMemory copy Recall the memory number to beCopy source Press the g button to selectPress the + button to display the confirmation screen Resetting to the default settings in the memory menu Initialization of the currently selected memoryInitialization of all the memories Glossary ReferenceCompatible signal types Signal type Active Component type Pixels Lines KHz Reference EnglishMaintenance Regular careReplacing the filter Replacing the lamp Loosen the lamp cover screwsLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningSpecifications OpticalControls GeneralDimensional drawing 119.1C2005 All Rights Reserved