Yamaha DPX-1300 Connecting to computer devices, Information for installers, For US model only

Page 20

Connecting to computer devices

You can use the following three methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and jacks you wish to use. The HDMI terminal does not support PC signals.

Input

Signal type

Connector type

INPUT A

RGB (Analog)

BNC jack x 5

INPUT B

RGB (Analog)

D-sub 15 pin

DVI

RGB (Digital)

DVI connector

						OUT		IN
DVI	HDMI						REMOTE	RS-232C	TRIGGER OUT
INPUT B				INPUT A
RGB/YPBPR/YCBCR	D4 VIDEO	G/Y	B/PB/CB	R/PR/CR	HD/SYNC	VD		S VIDEO	VIDEO

D-Sub monitorBNC monitor cable cable

Monitor output terminal

DVI cable

Computer devices

Information for installers

(for US model only)

+polarity (inside)

-polarity (outside) (GND)

- polarity

+polarity

Use the supplied trigger-out DC plug to control external components.

Be sure to solder the wires from an external component to the plug terminals with the correct polarities, as illustrated at left.

Warning

•Soldering the wires to terminals with incorrect polarity may cause bodily injury or may damage this unit and the external component connected to this unit with this cable.

16

Image 20

Contents DPX-1300 Important Safety Instructions We Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Features EnglishMain unit Front panel and controls Main unit Rear panel / Connections Controls and functionsRemote control functions Remote control English Light switchRemote control code switch Remote control cable jackLoading the batteries into the remote control Using the remote control with a wired connectionUse within a left/right arc of 30 degrees Limits for using the remote controlDistance to sensor Angle to sensor If you have not installed the main unit or screen PreparationTurn the power on and selecting an image for projection PrepararionMounting the projector on the ceiling Setting up the DPX-1300Mounting the projector on a table Installation When using a 169 screenWhen using a 43 screen Projection distanceKeystone adjustment Using Zoom to adjust image positionUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionConnecting to AV components ConnectionConnecting to computer devices Information for installersFor US model only + polarity inside Polarity outside GNDChecking installation and connections Pre-operation checkProjection English Projection preparations completePress the STANDBY/ON button Button on the remote control Turning the projector power onTurning the power on Press the STANDBY/ON button Placing the DPX-1300 in standby modeLamp may blink when half lit. This is not a defect Projection image signal Selecting an input signalSelecting using the Input button Press the + button to open the submenu Using the Input button to select a signalProjection Remote cotrol Selecting a display aspect for a projection imagePress the Aspect button Display aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesAdjusting the image Adjusting the vertical position V.POS buttonPattern button Crosshatch pattern Grayscale pattern Color bar patternAdjusting the size of an image Zoom button Menu configurations Menu screenMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Menu Level Adjustment Adjusts the iris OpticalAdjusts the analog input signal gain and offset settings White PeakingSignal Menu EnglishSignal Level Signal StatusOvershoot Supp. Range Overshoot Supp. LevelInitial Setup Menu Color MessageTrigger Out Baud RateReset button Remote control only Remote ControlMenu operations Operation button functionsMenu operations 1 with no submenu Press the Menu button to openMenu screen Press the + or button to select a menu groupPress the + or button to select a suitable setting Setting method depends on the item selectedRemote Control Main Unit Menu Button Remote Control Main UnitPress the h or g button to adjust item settings Menu operations 2 with submenusPress the + button to move to the submenu Appears to the right of items that contain a submenuSpecial operations See page 32 for datails about each color itemName of the selected item appears here Example Using the color temperature fixed modeExample Color temperature fixed mode Changing the position of the menu screen Resetting the selected settingsResetting all the settings Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonAdjusting image quality using the inline menu Example Using the inline menuInline menu composition Inline menu item listMemory configurations Saving memory settingsUsing the remote control Using the menuMemory function English Press the g button to select Memory number status fromBottom of the screen Press the h or g button to select a memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Select the memory number youMemory copy Recall the memory number to beCopy source Press the g button to selectPress the + button to display the confirmation screen Resetting to the default settings in the memory menu Initialization of the currently selected memoryInitialization of all the memories Glossary ReferenceCompatible signal types Signal type Active Component type Pixels Lines KHz Reference EnglishReplacing the filter MaintenanceRegular care Lamp cover screws Replacing the lampLoosen the lamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningSpecifications OpticalControls GeneralDimensional drawing 119.1C2005 All Rights Reserved