Yamaha DPX-1300 manual Connecting to AV components, Connection

Page 19

7Connection

Connecting to AV components

This unit is equipped with 7 types of video input jacks for AV components. Follow the diagram to connect AV components to this unit, taking care to use cables and adapters that match the input jacks.

Input	Signal type	Connector type

VIDEO	Composite video	Pin jack
S VIDEO	S-Video	Mini DIN connector
INPUT A	Component video/RGB video	BNC connector x 3-5
INPUT B	Component video/RGB video	D-sub 15 pin
D4 VIDEO	Component video	D connector
HDMI	Component video/RGB video (digital)	HDMI connector
DVI	RGB video (digital)	DVI connector

Warning

•Be sure to turn off the power of this unit and the source component before attempting connection.

•Connection methods and jack names may differ depending on the component you are attempting to connect. Refer to the owner’s manual for the component.

•Insert all plugs firmly to avoid noise or other problems.

HDMI cable (digital)

DVI cable (digital)

						OUT		IN
DVI	HDMI						REMOTE	RS-232C	TRIGGER OUT
INPUT B				INPUT A
RGB/YPBPR/YCBCR	D4 VIDEO	G/Y	B/PB/CB	R/PR/CR	HD/SYNC	VD		S VIDEO	VIDEO

7

D-sub monitor cable

Dconnector cable

BNC cable for
component connection	Video pin cable
	Video pin cable
	S-Video cable
Pin/BNC
adapters
Pin cable

Connection

				G/Y	B/PB/CBR/PR/CR
HDMI	DVI output	D1—4	D-sub	Pin jacks	BNC jacks	S-Video output	Video output
output	connector	output				jack	jack
connector		connectors

Component/RGB video output connectors

Image output from AV components

Memo

•Be sure to connect Y/PB/PR and Y/CB/CR to the jacks with the correct signals when connecting AV components to INPUT A. Refer to the owner’s manual of the source component for more information. You may need to make connections to HD/SYNC and VD for RGB video signals.

English

15

Image 19

Contents DPX-1300 Important Safety Instructions FCC Information for US customers only We Want You Listening For a LifetimeIii Table of contents Accessory check Inappropriate places for installationFeatures English FeaturesMain unit Front panel and controls Controls and functions Main unit Rear panel / ConnectionsRemote control functions Remote control cable jack Remote control EnglishLight switch Remote control code switchUsing the remote control with a wired connection Loading the batteries into the remote controlDistance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees Preparation If you have not installed the main unit or screenPrepararion Turn the power on and selecting an image for projectionMounting the projector on a table Setting up the DPX-1300Mounting the projector on the ceiling Projection distance InstallationWhen using a 169 screen When using a 43 screenUsing the adjusters to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using V.POS vertical position to adjust image positionConnection Connecting to AV components+ polarity inside Polarity outside GND Connecting to computer devicesInformation for installers For US model onlyProjection preparations complete Checking installation and connectionsPre-operation check Projection EnglishTurning the power on Turning the projector power onPress the STANDBY/ON button Button on the remote control Lamp may blink when half lit. This is not a defect Placing the DPX-1300 in standby modePress the STANDBY/ON button Selecting using the Input button Selecting an input signalProjection image signal Projection Using the Input button to select a signalPress the + button to open the submenu Press the Aspect button Selecting a display aspect for a projection imageRemote cotrol Display aspect types Representative examples Input signal typeInput imageDisplay aspectProjected imageCrosshatch pattern Grayscale pattern Color bar pattern Adjusting the imageAdjusting the vertical position V.POS button Pattern buttonAdjusting the size of an image Zoom button Menu screen Menu configurationsMenu item list Menu itemsLower level menu items Submenu ItemsMenu group items and functions Menu White Peaking Level AdjustmentAdjusts the iris Optical Adjusts the analog input signal gain and offset settingsMenu English SignalOvershoot Supp. Level Signal LevelSignal Status Overshoot Supp. RangeInitial Setup Baud Rate Menu ColorMessage Trigger OutOperation button functions Reset button Remote control onlyRemote Control Menu operationsPress the + or button to select a menu group Menu operations 1 with no submenuPress the Menu button to open Menu screenRemote Control Main Unit Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main Unit Menu ButtonAppears to the right of items that contain a submenu Press the h or g button to adjust item settingsMenu operations 2 with submenus Press the + button to move to the submenuSee page 32 for datails about each color item Special operationsExample Color temperature fixed mode Example Using the color temperature fixed modeName of the selected item appears here Resetting all the settings Resetting the selected settingsChanging the position of the menu screen Subtitle Zoom Resetting the lamp running timePress the button Changing the GammaInline menu item list Adjusting image quality using the inline menuExample Using the inline menu Inline menu compositionUsing the menu Memory configurationsSaving memory settings Using the remote controlPress the h or g button to select a memory number Memory function EnglishPress the g button to select Memory number status from Bottom of the screenSelect the memory number you Setting Memory LockMemory lock Deactivating Memory LockPress the g button to select Memory copyRecall the memory number to be Copy sourcePress the + button to display the confirmation screen Initialization of the currently selected memory Resetting to the default settings in the memory menuInitialization of all the memories Reference GlossaryCompatible signal types Reference English Signal type Active Component type Pixels Lines KHzRegular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws To protect the lamp, you cannot turn on TroubleshootingTroubleshooting Message Condition Message displayLED indicator State Meaning LED indicator meaningsGeneral SpecificationsOptical Controls119.1 Dimensional drawingC2005 All Rights Reserved