Yamaha DPX-1300 manual Representative examples

Page 28

Selecting an input signal

<Representative examples>

Input signal typeInput imageDisplay aspectProjected image

Normal

Standard 4:3 image

Smart Zoom

		Zoom
	Letter box	Subtitle Zoom
		SUBTITLE
		Cinema Zoom
		Squeeze
	Squeeze	Squeeze
		Cinema Squeeze
	14:9 image	14:9 Zoom
	Normal	Normal
	HDMI
	Cinema	Cinema Zoom
	Scope	Cinema Zoom
	Scope
	RGB PC	Normal
	Normal	Normal Through
	All

Squeeze

Squeeze Through

Image 28

Contents DPX-1300 Important Safety Instructions We Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Features EnglishMain unit Front panel and controls Main unit Rear panel / Connections Controls and functionsRemote control functions Remote control English Light switchRemote control code switch Remote control cable jackLoading the batteries into the remote control Using the remote control with a wired connectionDistance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationTurn the power on and selecting an image for projection PrepararionMounting the projector on a table Setting up the DPX-1300Mounting the projector on the ceiling Installation When using a 169 screenWhen using a 43 screen Projection distanceKeystone adjustment Using Zoom to adjust image positionUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionConnecting to AV components ConnectionConnecting to computer devices Information for installersFor US model only + polarity inside Polarity outside GNDChecking installation and connections Pre-operation checkProjection English Projection preparations completeTurning the power on Turning the projector power onPress the STANDBY/ON button Button on the remote control Lamp may blink when half lit. This is not a defect Placing the DPX-1300 in standby modePress the STANDBY/ON button Selecting using the Input button Selecting an input signalProjection image signal Projection Using the Input button to select a signalPress the + button to open the submenu Press the Aspect button Selecting a display aspect for a projection imageRemote cotrol Display aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesAdjusting the image Adjusting the vertical position V.POS buttonPattern button Crosshatch pattern Grayscale pattern Color bar patternAdjusting the size of an image Zoom button Menu configurations Menu screenMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Menu Level Adjustment Adjusts the iris OpticalAdjusts the analog input signal gain and offset settings White PeakingSignal Menu EnglishSignal Level Signal StatusOvershoot Supp. Range Overshoot Supp. LevelInitial Setup Menu Color MessageTrigger Out Baud RateReset button Remote control only Remote ControlMenu operations Operation button functionsMenu operations 1 with no submenu Press the Menu button to openMenu screen Press the + or button to select a menu groupPress the + or button to select a suitable setting Setting method depends on the item selectedRemote Control Main Unit Menu Button Remote Control Main UnitPress the h or g button to adjust item settings Menu operations 2 with submenusPress the + button to move to the submenu Appears to the right of items that contain a submenuSpecial operations See page 32 for datails about each color itemExample Color temperature fixed mode Example Using the color temperature fixed modeName of the selected item appears here Resetting all the settings Resetting the selected settingsChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonAdjusting image quality using the inline menu Example Using the inline menuInline menu composition Inline menu item listMemory configurations Saving memory settingsUsing the remote control Using the menuMemory function English Press the g button to select Memory number status fromBottom of the screen Press the h or g button to select a memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Select the memory number youMemory copy Recall the memory number to beCopy source Press the g button to selectPress the + button to display the confirmation screen Resetting to the default settings in the memory menu Initialization of the currently selected memoryInitialization of all the memories Glossary ReferenceCompatible signal types Signal type Active Component type Pixels Lines KHz Reference EnglishRegular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningSpecifications OpticalControls GeneralDimensional drawing 119.1C2005 All Rights Reserved