Yamaha DPX-1300 manual Dimensional drawing, 119.1

Page 69

Dimensional drawing

119.1

		SETTING
	MENU	INPUT	FAN	DPX-1000
STANDBY ON	ESCAPE	ASPECT	LAMP COVER TEMP	DIGITAL CINEMA PROJECTOR
		PATTERN

237.5 9"-3/8

(257.5 10"-1/8)

495 19"-1/2

4"-3/5

124.6

4"-7/8

465.4

18"-5/16

192.6 7"-9/16

			132.1	297.4
			5"-3/16	11"-3/4
124	4"-7/8	10	3/8	360	14"-3/16

RGB/YP P	INPUT	DVI
/YC	B
C
D4 VIDEO		HDMI
G/Y
B/P
/C
R/P /C	INPUT A
HD/SYNC
VD
		OUT
		REMOTE
		IN
S VIDEO		RS-232C
VIDEO		TRIGGER OUT

Reference

Specifications are subject to change without notice.

•This unit may interfere with reception if placed in close proximity to a radio or television receiver. Follow the instructions in this manual to install the unit correctly.

English

Image 69

Contents DPX-1300 Important Safety Instructions FCC Information for US customers only We Want You Listening For a LifetimeIii Table of contents Accessory check Inappropriate places for installationFeatures English FeaturesMain unit Front panel and controls Controls and functions Main unit Rear panel / ConnectionsRemote control functions Light switch Remote control EnglishRemote control code switch Remote control cable jackUsing the remote control with a wired connection Loading the batteries into the remote controlLimits for using the remote control Distance to sensor Angle to sensorUse within a left/right arc of 30 degrees Preparation If you have not installed the main unit or screenPrepararion Turn the power on and selecting an image for projectionSetting up the DPX-1300 Mounting the projector on a tableMounting the projector on the ceiling When using a 169 screen InstallationWhen using a 43 screen Projection distanceUsing Zoom to adjust image position Keystone adjustmentUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionConnection Connecting to AV componentsInformation for installers Connecting to computer devicesFor US model only + polarity inside Polarity outside GNDPre-operation check Checking installation and connectionsProjection English Projection preparations completeTurning the projector power on Turning the power onPress the STANDBY/ON button Button on the remote control Placing the DPX-1300 in standby mode Lamp may blink when half lit. This is not a defectPress the STANDBY/ON button Selecting an input signal Selecting using the Input buttonProjection image signal Using the Input button to select a signal ProjectionPress the + button to open the submenu Selecting a display aspect for a projection image Press the Aspect buttonRemote cotrol Display aspect types Representative examples Input signal typeInput imageDisplay aspectProjected imageAdjusting the vertical position V.POS button Adjusting the imagePattern button Crosshatch pattern Grayscale pattern Color bar patternAdjusting the size of an image Zoom button Menu screen Menu configurationsMenu item list Menu itemsLower level menu items Submenu ItemsMenu group items and functions Menu Adjusts the iris Optical Level AdjustmentAdjusts the analog input signal gain and offset settings White PeakingMenu English SignalSignal Status Signal LevelOvershoot Supp. Range Overshoot Supp. LevelInitial Setup Message Menu ColorTrigger Out Baud RateRemote Control Reset button Remote control onlyMenu operations Operation button functionsPress the Menu button to open Menu operations 1 with no submenuMenu screen Press the + or button to select a menu groupSetting method depends on the item selected Press the + or button to select a suitable settingRemote Control Main Unit Menu Button Remote Control Main UnitMenu operations 2 with submenus Press the h or g button to adjust item settingsPress the + button to move to the submenu Appears to the right of items that contain a submenuSee page 32 for datails about each color item Special operationsExample Using the color temperature fixed mode Example Color temperature fixed modeName of the selected item appears here Resetting the selected settings Resetting all the settingsChanging the position of the menu screen Subtitle Zoom Resetting the lamp running timePress the button Changing the GammaExample Using the inline menu Adjusting image quality using the inline menuInline menu composition Inline menu item listSaving memory settings Memory configurationsUsing the remote control Using the menuPress the g button to select Memory number status from Memory function EnglishBottom of the screen Press the h or g button to select a memory numberMemory lock Setting Memory LockDeactivating Memory Lock Select the memory number youRecall the memory number to be Memory copyCopy source Press the g button to selectPress the + button to display the confirmation screen Initialization of the currently selected memory Resetting to the default settings in the memory menuInitialization of all the memories Reference GlossaryCompatible signal types Reference English Signal type Active Component type Pixels Lines KHzMaintenance Regular careReplacing the filter Replacing the lamp Loosen the lamp cover screwsLamp cover screws To protect the lamp, you cannot turn on TroubleshootingTroubleshooting Message Condition Message displayLED indicator State Meaning LED indicator meaningsOptical SpecificationsControls General119.1 Dimensional drawingC2005 All Rights Reserved