Yamaha DPX-1300 manual Turning the projector power on, Turning the power on

Page 22

Turning the projector power on

◆Turning the power on

Always remove the lens cap before operating the main unit.

	STANDBY/ON
	STANDBY/ON
	indicator
ESCAPE	MENU
PATTERN	SETTING
ASPECT	INPUT
	LAMP COVER TEMP FAN

1.Insert the supplied power cable firmly into the AC inlet at the rear of the main unit, then insert the plug into an AC outlet.

The STANDBY/ON indicator lights red.

		AC inlet
		button STANDBY/ON button
AUTO
			STANDBY/ON
V. POS	ZOOM	FOCUS
IRIS	SETTING	PATT
		ESCAPE	MENU
ESCAPE		MENU
		PATTERN	SETTING
		ASPECT	INPUT
ASPECT		INPUT	LAMP COVER TEMP FAN
ASPECT		INPUT
Remote Control			Main unit

2.Press the STANDBY/ON button

(the button on the remote control).

The indicator blinks green and the lamp lights up in preparation for projection. After approximately 35 seconds, the indicator changes from blinking to steady green, indicating that the unit is ready to project.

Warning

•Do not remove the power cable while the STANDBY/ON indicator is blinking green or lit steady green. This could damage the lamp or reduce lamp life.

18

Image 22

Contents DPX-1300 Important Safety Instructions We Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Features EnglishMain unit Front panel and controls Main unit Rear panel / Connections Controls and functionsRemote control functions Remote control code switch Remote control EnglishLight switch Remote control cable jackLoading the batteries into the remote control Using the remote control with a wired connectionDistance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationTurn the power on and selecting an image for projection PrepararionMounting the projector on a table Setting up the DPX-1300Mounting the projector on the ceiling When using a 43 screen InstallationWhen using a 169 screen Projection distanceUsing V.POS vertical position to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using the adjusters to adjust image positionConnecting to AV components ConnectionFor US model only Connecting to computer devicesInformation for installers + polarity inside Polarity outside GNDProjection English Checking installation and connectionsPre-operation check Projection preparations completeTurning the power on Turning the projector power onPress the STANDBY/ON button Button on the remote control Lamp may blink when half lit. This is not a defect Placing the DPX-1300 in standby modePress the STANDBY/ON button Selecting using the Input button Selecting an input signalProjection image signal Projection Using the Input button to select a signalPress the + button to open the submenu Press the Aspect button Selecting a display aspect for a projection imageRemote cotrol Display aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesPattern button Adjusting the imageAdjusting the vertical position V.POS button Crosshatch pattern Grayscale pattern Color bar patternAdjusting the size of an image Zoom button Menu configurations Menu screenMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Menu Adjusts the analog input signal gain and offset settings Level AdjustmentAdjusts the iris Optical White PeakingSignal Menu EnglishOvershoot Supp. Range Signal LevelSignal Status Overshoot Supp. LevelInitial Setup Trigger Out Menu ColorMessage Baud RateMenu operations Reset button Remote control onlyRemote Control Operation button functionsMenu screen Menu operations 1 with no submenuPress the Menu button to open Press the + or button to select a menu groupRemote Control Main Unit Menu Button Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main UnitPress the + button to move to the submenu Press the h or g button to adjust item settingsMenu operations 2 with submenus Appears to the right of items that contain a submenuSpecial operations See page 32 for datails about each color itemExample Color temperature fixed mode Example Using the color temperature fixed modeName of the selected item appears here Resetting all the settings Resetting the selected settingsChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonInline menu composition Adjusting image quality using the inline menuExample Using the inline menu Inline menu item listUsing the remote control Memory configurationsSaving memory settings Using the menuBottom of the screen Memory function EnglishPress the g button to select Memory number status from Press the h or g button to select a memory numberDeactivating Memory Lock Setting Memory LockMemory lock Select the memory number youCopy source Memory copyRecall the memory number to be Press the g button to selectPress the + button to display the confirmation screen Resetting to the default settings in the memory menu Initialization of the currently selected memoryInitialization of all the memories Glossary ReferenceCompatible signal types Signal type Active Component type Pixels Lines KHz Reference EnglishRegular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningControls SpecificationsOptical GeneralDimensional drawing 119.1C2005 All Rights Reserved