Yamaha DPX-1300 manual Resetting the lamp running time, Subtitle Zoom

Page 49

<Resetting the lamp running time>

Reset the [Lamp Running Time] displayed on screen to “0”.

1.From the menu screen, select [Initial] [Lamp Running Time].

2.Press the + button to open the confirmation screen.

3.Press the h or g button to select [Yes].

4.Press the button to confirm.

Memo

•To cancel the operation and return to the menu screen, select [No].

Menu operations

				Move Menu Window
	Image		Signal		Initial	Setup

	Color System				Auto
	INPUT A Signal				Component
	INPUT A Sync Type				Auto
	INPUT B Signal				RGB TV
	INPUT B Sync Type				Auto
	HDMI Signal				Component
	DVI				Component
	Auto Power Off				Off	On
	Auto Input Search				Off	On
	Display Language				English
	Lamp Running Time				12 Hours
	Reset

	+ : Enter				Memory 1	VIDEO

				Move Menu Window

	Image		Signal		Initial	Setup

Press " " to reset lamp running time.

No

Yes

Lamp Running Time	12 Hours

: Fix	Memory 4	VIDEO

9

<Subtitle Zoom>

Use the [Subtitle Area] menu to adjust the size of the subtitle display area. Use [V Scroll] to adjust the vertical position of the subtitle display.

Menu

1.From the menu screen, select [Signal] [Display

Aspect Ratio] [Special].

2.Press the + button to enter the lower level selection menu.

3.Select [Subtitle Zoom] with h or g buttons.

4.Press the button.

“” appears to the right of [Subtitle zoom].

Memo

		Move Menu Window
Image	Signal		Initial	Setup

Special			Subtitle Zoom

			Cinema Zoom

Cinema Squeeze

14:9 Zoom

+ : Enter

Memory 1

VIDEO

•After the first time you carry out this procedure, “ ” appears beside [Subtitle Zoom] automatically.

English

45

Image 49

Contents DPX-1300 Important Safety Instructions FCC Information for US customers only We Want You Listening For a LifetimeIii Table of contents Accessory check Inappropriate places for installationFeatures English FeaturesMain unit Front panel and controls Controls and functions Main unit Rear panel / ConnectionsRemote control functions Light switch Remote control EnglishRemote control code switch Remote control cable jackUsing the remote control with a wired connection Loading the batteries into the remote controlDistance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees Preparation If you have not installed the main unit or screenPrepararion Turn the power on and selecting an image for projectionMounting the projector on a table Setting up the DPX-1300Mounting the projector on the ceiling When using a 169 screen InstallationWhen using a 43 screen Projection distanceUsing Zoom to adjust image position Keystone adjustmentUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionConnection Connecting to AV componentsInformation for installers Connecting to computer devicesFor US model only + polarity inside Polarity outside GNDPre-operation check Checking installation and connectionsProjection English Projection preparations completeTurning the power on Turning the projector power onPress the STANDBY/ON button Button on the remote control Lamp may blink when half lit. This is not a defect Placing the DPX-1300 in standby modePress the STANDBY/ON button Selecting using the Input button Selecting an input signalProjection image signal Projection Using the Input button to select a signalPress the + button to open the submenu Press the Aspect button Selecting a display aspect for a projection imageRemote cotrol Display aspect types Representative examples Input signal typeInput imageDisplay aspectProjected imageAdjusting the vertical position V.POS button Adjusting the imagePattern button Crosshatch pattern Grayscale pattern Color bar patternAdjusting the size of an image Zoom button Menu screen Menu configurationsMenu item list Menu itemsLower level menu items Submenu ItemsMenu group items and functions Menu Adjusts the iris Optical Level AdjustmentAdjusts the analog input signal gain and offset settings White PeakingMenu English SignalSignal Status Signal LevelOvershoot Supp. Range Overshoot Supp. LevelInitial Setup Message Menu ColorTrigger Out Baud RateRemote Control Reset button Remote control onlyMenu operations Operation button functionsPress the Menu button to open Menu operations 1 with no submenuMenu screen Press the + or button to select a menu groupSetting method depends on the item selected Press the + or button to select a suitable settingRemote Control Main Unit Menu Button Remote Control Main UnitMenu operations 2 with submenus Press the h or g button to adjust item settingsPress the + button to move to the submenu Appears to the right of items that contain a submenuSee page 32 for datails about each color item Special operationsExample Color temperature fixed mode Example Using the color temperature fixed modeName of the selected item appears here Resetting all the settings Resetting the selected settingsChanging the position of the menu screen Subtitle Zoom Resetting the lamp running timePress the button Changing the GammaExample Using the inline menu Adjusting image quality using the inline menuInline menu composition Inline menu item listSaving memory settings Memory configurationsUsing the remote control Using the menuPress the g button to select Memory number status from Memory function EnglishBottom of the screen Press the h or g button to select a memory numberMemory lock Setting Memory LockDeactivating Memory Lock Select the memory number youRecall the memory number to be Memory copyCopy source Press the g button to selectPress the + button to display the confirmation screen Initialization of the currently selected memory Resetting to the default settings in the memory menuInitialization of all the memories Reference GlossaryCompatible signal types Reference English Signal type Active Component type Pixels Lines KHzRegular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws To protect the lamp, you cannot turn on TroubleshootingTroubleshooting Message Condition Message displayLED indicator State Meaning LED indicator meaningsOptical SpecificationsControls General119.1 Dimensional drawingC2005 All Rights Reserved