Yamaha DPX-1300 manual Setup

Page 40

Menu items

◆Setup

Location

Designate the location of the main unit.

Choices: [Front/Table] [Front/Ceiling] [Rear/Table] [Rear/Ceiling] (☞ page 12)

V Keystone Correction

Adjusts the projection angle of the image.

If you do not install the projector at right angles to the screen, the image will be trapezoidally distorted. You can electronically correct this distortion using this function to adjust the width without changing the height of the image. Increase the keystone value (0 to +50 ) when the upper part of the image is overly wide, and reduce it (-50 to 0 ) when the lower part is overly wide.

When the upper part of

When the lower part of

the image is wider than the lower part

the image is wider than the upper part

Increase the value

Decrease the value

in the positive (+) direction

in the negative (-) direction

H Keystone Correction

Adjusts the projection angle of the image.

If you do not install the projector at right angles to the screen, the image will be trapezoidally distorted. You can electronically correct this distortion using this function to adjust the height without changing the width of the image. Increase the keystone value (0 to +50 ) when the right side of the image is overly high, and reduce it (-50 to 0 ) when the left side is overly high.

When the right side of

When the left side of

the image is higher than the left side

the image is higher than the right side

Increase the value

Decrease the value

in the positive (+) direction

in the negative (-) direction

Remote Control Sensor

Sets the remote control sensor.

The main unit has two remote control sensors, one on the front panel and one on the rear, which this setting allows you to switch between. The remote control functions regardless of the setting of this parameter if you use a wired connection to connect it to the main unit. Choices: Front & Rear/Front/Rear/Off

Remote Control ID

Lens Adjustment Lock

Sets the remote control ID.

Selects ID1 or ID2 for each main unit when operating two main units with one remote control. You can select the controllable main unit with the remote control code switch on the remote control.

Choices: ID1/ID2

Locks the lens adjustment function.

Locks the lens so that you cannot change the V.POS, ZOOM, and FOCUS settings accidentally when set to [ON]. Set to [OFF] to cancel this function.

Lamp Power

Lowers the power supply to the lamp.

You can adjust the power supplied to the lamp within the range of 80 to 100%.

36

Page 39 Page 41
Image 40
Page 39 Page 41
Contents DPX-1300 Important Safety Instructions We Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Features EnglishMain unit Front panel and controls Main unit Rear panel / Connections Controls and functionsRemote control functions Remote control English Light switchRemote control code switch Remote control cable jackLoading the batteries into the remote control Using the remote control with a wired connectionDistance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationTurn the power on and selecting an image for projection PrepararionMounting the projector on a table Setting up the DPX-1300Mounting the projector on the ceiling Installation When using a 169 screenWhen using a 43 screen Projection distanceKeystone adjustment Using Zoom to adjust image positionUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionConnecting to AV components ConnectionConnecting to computer devices Information for installersFor US model only + polarity inside Polarity outside GNDChecking installation and connections Pre-operation checkProjection English Projection preparations completeTurning the power on Turning the projector power onPress the STANDBY/ON button Button on the remote control Lamp may blink when half lit. This is not a defect Placing the DPX-1300 in standby modePress the STANDBY/ON button Selecting using the Input button Selecting an input signalProjection image signal Projection Using the Input button to select a signalPress the + button to open the submenu Press the Aspect button Selecting a display aspect for a projection imageRemote cotrol Display aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesAdjusting the image Adjusting the vertical position V.POS buttonPattern button Crosshatch pattern Grayscale pattern Color bar patternAdjusting the size of an image Zoom button Menu configurations Menu screenMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Menu Level Adjustment Adjusts the iris OpticalAdjusts the analog input signal gain and offset settings White PeakingSignal Menu EnglishSignal Level Signal StatusOvershoot Supp. Range Overshoot Supp. LevelInitial Setup Menu Color MessageTrigger Out Baud RateReset button Remote control only Remote ControlMenu operations Operation button functionsMenu operations 1 with no submenu Press the Menu button to openMenu screen Press the + or button to select a menu groupPress the + or button to select a suitable setting Setting method depends on the item selectedRemote Control Main Unit Menu Button Remote Control Main UnitPress the h or g button to adjust item settings Menu operations 2 with submenusPress the + button to move to the submenu Appears to the right of items that contain a submenuSpecial operations See page 32 for datails about each color itemExample Color temperature fixed mode Example Using the color temperature fixed modeName of the selected item appears here Resetting all the settings Resetting the selected settingsChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonAdjusting image quality using the inline menu Example Using the inline menuInline menu composition Inline menu item listMemory configurations Saving memory settingsUsing the remote control Using the menuMemory function English Press the g button to select Memory number status fromBottom of the screen Press the h or g button to select a memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Select the memory number youMemory copy Recall the memory number to beCopy source Press the g button to selectPress the + button to display the confirmation screen Resetting to the default settings in the memory menu Initialization of the currently selected memoryInitialization of all the memories Glossary ReferenceCompatible signal types Signal type Active Component type Pixels Lines KHz Reference EnglishRegular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningSpecifications OpticalControls GeneralDimensional drawing 119.1C2005 All Rights Reserved
Top Page Image Contents