Barco E-2320 C (SE) system manual Canadian notice, FCC Compliance Information display controller

Page 10

Preface

Canadian notice

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.

FCC Compliance Information (display controller)

CLASS B:

This Barco Graphics Controller complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference, and

1.this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Re-orient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

10

Image 10
Contents System Manual This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Troubleshooting Technical Information Preface Preface Trademarks FCC notice displayCanadian notice FCC Compliance Information display controllerPreface Environmental information Disposal InformationInformation for China Rohs compliance Part NameEnvironmental information Power connection Safety InstructionsDegree of safety flammable anesthetic mixture General RecommendationsWater and moisture InstallationVentilation This apparatus conforms to Operating precautionsNational Scandinavian Deviations for Cl Explanation of symbols Symbols on the display and / or power supplySymbols used throughout the manual This page intentionally left blank Introduction Introduction Display OverviewSingle display or complete system? Long-term stabilizationPower saving Tilt & swivel basePackage contents Parts, controls and connectors FrontRear USB upstream port USB 1.1 standard is supported Installation Installation Installation precautions PrecautionsInstalling your Barco display controller OverviewQuick installation Which PCIe slot to useDetailed installation To perform a quick installationInstalling your Barco display controller Connecting your Barco displays Turning on your system Mxrt 5100 and Mxrt 7100 BaseplateInstalling your Barco display controller After unpacking the display Display installationAdjust the panel orientation To remove the clipTo change the panel orientation Power connection To connect the powerDisplay installation Connecting DVI signals Two displays Connecting DVI signals One displayVideo connection Connecting analog video USB connectionCable routing Routing the signal cablesTo connect the USB cable To put the foot cover in place Attaching the display to an arm To attach the display to an arm standScrews M4 x 8mm Installing drivers and software Driver and software installation prerequisitesSetup.exe Express Installation or Custom Installation Automated display configuration Command line Silent Install of Drivers and Software Installing drivers and software Operation Operation Accessing the Barco tab Barco Mxrt control panel settingsProperties Barco System Report Advanced Properties MediCal QAWebSmoothvision Device details Activating a configuration profile Barco Configuring the Windows desktop Stand-by switching Display operationOn-screen display How to navigate through the on-screen displayAbout the on-screen display When do you need to use the Autoset function? Using the Autoset functionRequired test pattern To perform geometry adjustments Adjusting GeometryTo perform Autoset You can perform the following adjustments Contrast adjustmentTo adjust Contrast To return to calibrated position Brightness adjustmentTo adjust brightness Additional informationColor temperature selection To modify a color temperature definitionTo disable user controls Locking and unlocking user controlsTo enable user controls Complete OSD overview Main menuAutoset menu is not available in DVI mode AutosetVideo Brightness Video ContrastLuminance Adjustments Geometry Adjustments Phase Input SelectionSettings Information General Information Information Current Input FormatCleaning Cleaning To clean the LCD panel Proceed as followsIf this is the case, clean the panel as described below Troubleshooting Troubleshooting General tips Problems and solutions Troubleshooting Select the function Preferred Input Freq Technical Information Technical Information Technical specifications Technical specifications Connector pin assignments DVI connectorSub 15 connector analog video Sub 15 pin layoutDisplay Function GlossaryCalibration Display Controller headPresets and Internal memory system DicomWarranty Statement 100 101 102 103 K5904185-00