Barco E-2320 C (SE) Using the Autoset function, When do you need to use the Autoset function?

Page 67

Display operation

2.To enter into a menu or move to a lower level of the menu structure, rotate the control wheel to select the desired menu. Next, press the wheel shortly.

3.To exit from a menu or return to a higher level of the menu structure, rotate the control wheel to select EXIT. Next, press the control wheel shortly.

If you do this when you are in the Main Menu, you exit the menu system.

4.To change an adjustment value, rotate the control wheel to select the adjustment and press the wheel shortly. The adjustment name appears, as well as the current adjustment value. Rotate the wheel to change the value. When done, press the wheel shortly to confirm the change and return to the menu.

Using the Autoset function

* Not available in DVI mode

When do you need to use the Autoset function?

The first time you use the display with analog video connected.

After connecting or selecting another analog video source (e.g., changing the PC resolution).

In case you notice the image geometry or positioning is not as desired.

Required test pattern

To obtain good results, the image on screen during the Autoset function should meet the following requirements:

The edges of the image should have an intensity of at least 15% video amplitude. E.g., a Windows desktop pattern would be a good image, provided the background is not too dark.

67

Image 67
Contents System Manual This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Troubleshooting Technical Information Preface Preface FCC notice display TrademarksFCC Compliance Information display controller Canadian noticePreface Disposal Information Environmental informationPart Name Information for China Rohs complianceEnvironmental information General Recommendations Safety InstructionsDegree of safety flammable anesthetic mixture Power connectionWater and moisture InstallationVentilation This apparatus conforms to Operating precautionsNational Scandinavian Deviations for Cl Symbols on the display and / or power supply Explanation of symbolsSymbols used throughout the manual This page intentionally left blank Introduction Introduction Long-term stabilization OverviewSingle display or complete system? DisplayTilt & swivel base Power savingPackage contents Front Parts, controls and connectorsRear USB upstream port USB 1.1 standard is supported Installation Installation Precautions Installation precautionsOverview Installing your Barco display controllerWhich PCIe slot to use Quick installationTo perform a quick installation Detailed installationInstalling your Barco display controller Connecting your Barco displays Mxrt 5100 and Mxrt 7100 Baseplate Turning on your systemInstalling your Barco display controller To remove the clip Display installationAdjust the panel orientation After unpacking the displayTo change the panel orientation To connect the power Power connectionDisplay installation Connecting DVI signals Two displays Connecting DVI signals One displayVideo connection USB connection Connecting analog videoCable routing Routing the signal cablesTo connect the USB cable To put the foot cover in place To attach the display to an arm stand Attaching the display to an armScrews M4 x 8mm Driver and software installation prerequisites Installing drivers and softwareSetup.exe Express Installation or Custom Installation Automated display configuration Command line Silent Install of Drivers and Software Installing drivers and software Operation Operation Accessing the Barco tab Barco Mxrt control panel settingsProperties Barco System Report MediCal QAWeb Advanced PropertiesSmoothvision Device details Activating a configuration profile Barco Configuring the Windows desktop Display operation Stand-by switchingOn-screen display How to navigate through the on-screen displayAbout the on-screen display When do you need to use the Autoset function? Using the Autoset functionRequired test pattern To perform geometry adjustments Adjusting GeometryTo perform Autoset You can perform the following adjustments Contrast adjustmentTo adjust Contrast Additional information Brightness adjustmentTo adjust brightness To return to calibrated positionTo modify a color temperature definition Color temperature selectionLocking and unlocking user controls To disable user controlsTo enable user controls Main menu Complete OSD overviewAutoset Autoset menu is not available in DVI modeVideo Brightness Video ContrastLuminance Adjustments Geometry Input Selection Adjustments PhaseSettings Information Current Input Format Information General InformationCleaning Cleaning Proceed as follows To clean the LCD panelIf this is the case, clean the panel as described below Troubleshooting Troubleshooting General tips Problems and solutions Troubleshooting Select the function Preferred Input Freq Technical Information Technical Information Technical specifications Technical specifications DVI connector Connector pin assignmentsSub 15 pin layout Sub 15 connector analog videoDisplay Controller head GlossaryCalibration Display FunctionDicom Presets and Internal memory systemWarranty Statement 100 101 102 103 K5904185-00