Barco E-2320 C (SE) system manual Water and moisture, Ventilation, Installation

Page 16

Safety Instructions

Power cord with CEE 7 plug: The colors of the mains lead are colored in accordance with the following code: Green-and-yellow: Earth (safety earth), Blue: Neutral, Brown: Line

Power cord with ANSI 73.11 plug: The wires of the power cord are colored in accordance with the following code: Green/yellow: ground, White: neutral, Black: line (live)

Do not overload wall outlets and extension cords as this may result in fire or electric shock.

Mains lead protection (U.S.: Power cord): Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them, paying particular attention to cords at plugs and receptacles.

Water and moisture

Never expose the display to rain or moisture.

Never use the display near water - e.g. near a bathtub, washbasin, swimming pool, kitchen sink, laundry tub or in a wet basement.

Ventilation

Do not cover or block the ventilation openings in the cover of the set. When installing the display in a cupboard or another closed location, heed the necessary space between the set and the sides of the cupboard.

Installation

Place the display on a flat, solid and stable surface that can bear the weight of at least 3 displays. If you use an unstable cart or stand, the display may fall, causing serious injury to a child or adult, and serious damage to the equipment.

More warnings in the Installation chapter.

16

Image 16
Contents System Manual This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Troubleshooting Technical Information Preface Preface Trademarks FCC notice displayCanadian notice FCC Compliance Information display controllerPreface Environmental information Disposal InformationInformation for China Rohs compliance Part NameEnvironmental information Safety Instructions Degree of safety flammable anesthetic mixturePower connection General RecommendationsWater and moisture InstallationVentilation This apparatus conforms to Operating precautionsNational Scandinavian Deviations for Cl Explanation of symbols Symbols on the display and / or power supplySymbols used throughout the manual This page intentionally left blank Introduction Introduction Overview Single display or complete system?Display Long-term stabilizationPower saving Tilt & swivel basePackage contents Parts, controls and connectors FrontRear USB upstream port USB 1.1 standard is supported Installation Installation Installation precautions PrecautionsInstalling your Barco display controller OverviewQuick installation Which PCIe slot to useDetailed installation To perform a quick installationInstalling your Barco display controller Connecting your Barco displays Turning on your system Mxrt 5100 and Mxrt 7100 BaseplateInstalling your Barco display controller Display installation Adjust the panel orientationAfter unpacking the display To remove the clipTo change the panel orientation Power connection To connect the powerDisplay installation Connecting DVI signals Two displays Connecting DVI signals One displayVideo connection Connecting analog video USB connectionCable routing Routing the signal cablesTo connect the USB cable To put the foot cover in place Attaching the display to an arm To attach the display to an arm standScrews M4 x 8mm Installing drivers and software Driver and software installation prerequisitesSetup.exe Express Installation or Custom Installation Automated display configuration Command line Silent Install of Drivers and Software Installing drivers and software Operation Operation Accessing the Barco tab Barco Mxrt control panel settingsProperties Barco System Report Advanced Properties MediCal QAWebSmoothvision Device details Activating a configuration profile Barco Configuring the Windows desktop Stand-by switching Display operationOn-screen display How to navigate through the on-screen displayAbout the on-screen display When do you need to use the Autoset function? Using the Autoset functionRequired test pattern To perform geometry adjustments Adjusting GeometryTo perform Autoset You can perform the following adjustments Contrast adjustmentTo adjust Contrast Brightness adjustment To adjust brightnessTo return to calibrated position Additional informationColor temperature selection To modify a color temperature definitionTo disable user controls Locking and unlocking user controlsTo enable user controls Complete OSD overview Main menuAutoset menu is not available in DVI mode AutosetVideo Brightness Video ContrastLuminance Adjustments Geometry Adjustments Phase Input SelectionSettings Information General Information Information Current Input FormatCleaning Cleaning To clean the LCD panel Proceed as followsIf this is the case, clean the panel as described below Troubleshooting Troubleshooting General tips Problems and solutions Troubleshooting Select the function Preferred Input Freq Technical Information Technical Information Technical specifications Technical specifications Connector pin assignments DVI connectorSub 15 connector analog video Sub 15 pin layoutGlossary CalibrationDisplay Function Display Controller headPresets and Internal memory system DicomWarranty Statement 100 101 102 103 K5904185-00