Barco E-2320 C (SE) system manual Proceed as follows, To clean the LCD panel

Page 83

Cleaning

Precautions

Take care not to damage or scratch the front filter or LCD panel. Be careful with rings or other jewelry that can touch the front filter.

Do not apply pressure on the front filter or LCD panel.

Do not apply or spray liquid directly to the front filter, panel or cabinet as excess liquid may cause damage to internal electronics. Instead, apply the liquid to the cleaning cloth.

Proceed as follows:

Clean the cabinet using a soft cotton cloth, lightly moistened with a recognized cleaning product for medical equipment.

Repeat with water only.

Wipe dry with a dry cloth.

The cabinet has been tested for resistance to the following products:

Cidex, Betadine

Alcohol (Isopropyl and Ethyl)

Ammonia-based cleaners (Windex)

Aquasonic Gel

To clean the LCD panel:

Dust particles on the LCD panel may be blown away by using a dust remover. E.g., DUST OFF 67 (KONTAKT Chemie).

A dust remover is composed of a blend of compressed liquid gases functioning as propellant. They provide a jet of dry inert gas that acts like compressed air for a quick and safe removal of dust particles and other dry contaminants on the surface of the lcd panel or the glass panel.

83

Image 83
Contents System Manual This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Troubleshooting Technical Information Preface Preface FCC notice display TrademarksFCC Compliance Information display controller Canadian noticePreface Disposal Information Environmental informationPart Name Information for China Rohs complianceEnvironmental information General Recommendations Safety InstructionsDegree of safety flammable anesthetic mixture Power connectionVentilation InstallationWater and moisture National Scandinavian Deviations for Cl Operating precautionsThis apparatus conforms to Symbols on the display and / or power supply Explanation of symbolsSymbols used throughout the manual This page intentionally left blank Introduction Introduction Long-term stabilization OverviewSingle display or complete system? DisplayTilt & swivel base Power savingPackage contents Front Parts, controls and connectorsRear USB upstream port USB 1.1 standard is supported Installation Installation Precautions Installation precautionsOverview Installing your Barco display controllerWhich PCIe slot to use Quick installationTo perform a quick installation Detailed installationInstalling your Barco display controller Connecting your Barco displays Mxrt 5100 and Mxrt 7100 Baseplate Turning on your systemInstalling your Barco display controller To remove the clip Display installationAdjust the panel orientation After unpacking the displayTo change the panel orientation To connect the power Power connectionDisplay installation Video connection Connecting DVI signals One displayConnecting DVI signals Two displays USB connection Connecting analog videoTo connect the USB cable Routing the signal cablesCable routing To put the foot cover in place To attach the display to an arm stand Attaching the display to an armScrews M4 x 8mm Driver and software installation prerequisites Installing drivers and softwareSetup.exe Express Installation or Custom Installation Automated display configuration Command line Silent Install of Drivers and Software Installing drivers and software Operation Operation Properties Barco Mxrt control panel settingsAccessing the Barco tab Barco System Report MediCal QAWeb Advanced PropertiesSmoothvision Device details Activating a configuration profile Barco Configuring the Windows desktop Display operation Stand-by switchingAbout the on-screen display How to navigate through the on-screen displayOn-screen display Required test pattern Using the Autoset functionWhen do you need to use the Autoset function? To perform Autoset Adjusting GeometryTo perform geometry adjustments To adjust Contrast Contrast adjustmentYou can perform the following adjustments Additional information Brightness adjustmentTo adjust brightness To return to calibrated positionTo modify a color temperature definition Color temperature selectionLocking and unlocking user controls To disable user controlsTo enable user controls Main menu Complete OSD overviewAutoset Autoset menu is not available in DVI modeLuminance Video ContrastVideo Brightness Adjustments Geometry Input Selection Adjustments PhaseSettings Information Current Input Format Information General InformationCleaning Cleaning Proceed as follows To clean the LCD panelIf this is the case, clean the panel as described below Troubleshooting Troubleshooting General tips Problems and solutions Troubleshooting Select the function Preferred Input Freq Technical Information Technical Information Technical specifications Technical specifications DVI connector Connector pin assignmentsSub 15 pin layout Sub 15 connector analog videoDisplay Controller head GlossaryCalibration Display FunctionDicom Presets and Internal memory systemWarranty Statement 100 101 102 103 K5904185-00