Barco E-2320 C (SE) system manual Installing your Barco display controller, Overview

Page 32

Installing your Barco display controller

Installing your Barco display controller

This chapter will guide you through the physical installation of the display controller(s) for your BARCO Display System.

CAUTION – Wear a grounded, protective ESD strap when handling or during installation of the display controller. Electrostatic charges can damage the display controller.

Overview

Prior to installing the display controller(s) for your BARCO Display System in your PC please take a few minutes to familiarize yourself with both the display controller(s) and the PCIe slots in your computer.

Types of display controllers for Nio Display Systems

There are four different models of display controllers available for your BARCO NIO Display System.

Board Model

VGA Jumper

Recommended PCIe Slot

BARCO NIO MXRT 2100

No

x16

BARCO NIO MXRT 5100

No

x16

BARCO NIO MXRT 7100

No

x16

BARCOMED CORONIS PCIe

Yes

x8

If you are using the BARCOMED CORONIS PCIe display controller, you will need to decide if you are going to use its on-board VGA capabilities. If you are, check the setting of the Jumper at J-1 on the display controller (see figure 3). By default, VGA should be enabled, on the top two pins. To disable the on-board VGA capabilities of you BARCOMED CORONIS PCIe display controller move the jumper so that it is on the middle and bottom pins.

32

Image 32
Contents System Manual This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Troubleshooting Technical Information Preface Preface Trademarks FCC notice displayCanadian notice FCC Compliance Information display controllerPreface Environmental information Disposal InformationInformation for China Rohs compliance Part NameEnvironmental information Safety Instructions Degree of safety flammable anesthetic mixturePower connection General RecommendationsVentilation InstallationWater and moisture National Scandinavian Deviations for Cl Operating precautionsThis apparatus conforms to Explanation of symbols Symbols on the display and / or power supplySymbols used throughout the manual This page intentionally left blank Introduction Introduction Overview Single display or complete system?Display Long-term stabilizationPower saving Tilt & swivel basePackage contents Parts, controls and connectors FrontRear USB upstream port USB 1.1 standard is supported Installation Installation Installation precautions PrecautionsInstalling your Barco display controller OverviewQuick installation Which PCIe slot to useDetailed installation To perform a quick installationInstalling your Barco display controller Connecting your Barco displays Turning on your system Mxrt 5100 and Mxrt 7100 BaseplateInstalling your Barco display controller Display installation Adjust the panel orientationAfter unpacking the display To remove the clipTo change the panel orientation Power connection To connect the powerDisplay installation Video connection Connecting DVI signals One displayConnecting DVI signals Two displays Connecting analog video USB connectionTo connect the USB cable Routing the signal cablesCable routing To put the foot cover in place Attaching the display to an arm To attach the display to an arm standScrews M4 x 8mm Installing drivers and software Driver and software installation prerequisitesSetup.exe Express Installation or Custom Installation Automated display configuration Command line Silent Install of Drivers and Software Installing drivers and software Operation Operation Properties Barco Mxrt control panel settingsAccessing the Barco tab Barco System Report Advanced Properties MediCal QAWebSmoothvision Device details Activating a configuration profile Barco Configuring the Windows desktop Stand-by switching Display operationAbout the on-screen display How to navigate through the on-screen displayOn-screen display Required test pattern Using the Autoset functionWhen do you need to use the Autoset function? To perform Autoset Adjusting GeometryTo perform geometry adjustments To adjust Contrast Contrast adjustmentYou can perform the following adjustments Brightness adjustment To adjust brightnessTo return to calibrated position Additional informationColor temperature selection To modify a color temperature definitionTo disable user controls Locking and unlocking user controlsTo enable user controls Complete OSD overview Main menuAutoset menu is not available in DVI mode AutosetLuminance Video ContrastVideo Brightness Adjustments Geometry Adjustments Phase Input SelectionSettings Information General Information Information Current Input FormatCleaning Cleaning To clean the LCD panel Proceed as followsIf this is the case, clean the panel as described below Troubleshooting Troubleshooting General tips Problems and solutions Troubleshooting Select the function Preferred Input Freq Technical Information Technical Information Technical specifications Technical specifications Connector pin assignments DVI connectorSub 15 connector analog video Sub 15 pin layoutGlossary CalibrationDisplay Function Display Controller headPresets and Internal memory system DicomWarranty Statement 100 101 102 103 K5904185-00