Brother HL-4070CDW Installing the printer driver, For Mac OS 10.2.4 to 10.2.8 users Go to step

Page 44

STEP 2 Installing the Printer Driver

Macintosh®

Network

Wireless

Macintosh®

9 Put the printer in SecureEasySetup™ mode using the control panel.

1Press any of the Menu buttons (+, -, OK or Back) to take the printer offline.

Ready

h

Select ab or OK

Machine Info.

2Press the + or - button to select LAN.

Select ab or OK

LAN

3Press OK to move to the next menu level.

LAN

Wired

4Press the + or - button to select WLAN.

LAN

WLAN

5Press the + or - button to select

Setup WLAN in WLAN menu.

WLAN

Setup WLAN

6Press OK to move to select the next level.

Setup WLAN

Setup Wizard

7Press the + or - button to select

SecureEasySetup.

Setup WLAN

SecureEasySetup

8Press OK.

If the following message appears, press OK again.

9The wireless network connection status using the SecureEasySetup™ software will be displayed; Connecting WLAN,

Connected or Connection NG.

Connecting WLAN is displayed when the print server is trying to make connections to your router or access point. Wait till either Connected or

Connection NG is displayed.

Connected is displayed when the print server is successfully connected to your router or access point. You can now use your printer in a wireless network.

Connection NG is displayed when the print server has not successfully connected to your router or access point. Try starting from 3 again. If the same message is displayed again, reset the print server back to the default factory settings and try again.

10 Click Finish. Relocate the printer to a location that is within range of your access point.

Installing the printer driver

Improper Setup

•DO NOT try to cancel any of the screens during this installation.

•If your wireless settings fail, and error message will appear during the installation of printer driver and the installation will be terminated. If you encounter this failure, please go to step 3 and setup the wireless connection again.

11 The driver installation starts.

For Mac OS® 10.3 or greater users:

Go to step 12.

WLAN Enable?

On

Note

The message above only appears when the wireless setting is disable.

For Mac OS® 10.2.4 to 10.2.8 users: Go to step 14.

42

Image 44

Contents Quick Setup Guide Symbols used in this guide Table of Contents Safety Precautions To Use the Printer SafelySafety Precautions Regulations Industry Canada Compliance Statement For CanadaIEC 60825-1 specification 220 to 240 volt model only For Finland and SwedenVaroitus VarningImportant For Your Safety IT power system For Norway onlyWiring information for UK Disconnect deviceWhat is in the box? Getting StartedControl panel Supplied CD-ROM Setting Up the Machine Put the CD-ROM into the CD-ROM driveRemove the packing materials from the printer Installing the toner cartridges Load paper in the paper trayPrint a test Do not connect the interface cable yetSetting your language on the control panel Installing the Printer Driver StepClick USB cable users Click Install Printer Driver on the menu screenFor USB interface cable users Setup is now complete Installing the driver and connecting the printer to Click Install Printer Driver on the menuFor parallel interface cable users Your computerTurn on the printer power switch For wired network interface cable users Click Network cable usersChoose Brother Peer-to-Peer Network For shared network printer users Choose Network Shared Printer, and then click Next For wireless network users Infrastructure ModeConfirm your network environment Click Install Printer Driver Click Wireless Network usersChoose Wireless Setup and Driver Install LAN Installing the printer driver Choose Standard Installation, and then click NextConfiguration in Infrastructure mode Set the wireless network enable using the contol panel„ If you can temporarily connect with a network cable Record the current wireless Select and right click Improper Setup Next Connecting the printer to your Macintosh Installing the driverFor Mac OS 10.3 or greater users Setup is now complete For Mac OS 10.2.4 to 10.2.8 usersFor Mac OS 10.2.4 to 10.2.8 users Setup is now complete Click Print Center, then Quit Print CenterFor network interface cable users Installing the Printer Driver Network Wireless Confirm your network environment SecureEasySetup function of my access Choose I’d like to useFor Mac OS 10.2.4 to 10.2.8 users Go to step For Mac OS 10.3 or greater users Setup is now complete Configuration in Infrastructure mode Choose Manual and then click Next Click the Network tab to see the available Your wireless network is connected successfully This installation If your wireless settings fail, and errorMessage will appear during the installation Printer driver and the installation will beInstalling the Printer Driver For Network Users BRAdmin Light utility For Windows usersClick Install Other Drivers or Utilities on the menu screen BRAdmin Light utility For Mac OS X users Choose Library, Printers, Brother and then UtilitiesNetwork default settings Print the Printer SettingsConsumables Consumables and OptionsOptions Other Information Shipment of the printerCopyright and License LR1447001