8e6 Technologies SL-002-002, HL-022-002, HL-002-002 quick start General Safety Information

Page 20

General Safety Information

Server Operation and Maintenance Precautions

Warning:

Observe the following safety precautions during server operation and maintenance:

WARNING: If the server is used in a manner not specified by the manufacturer, the protection provided by the server may be impaired.

WARNING: 8e6 Technologies is not responsible for regulatory compliance of any server that has been modified. Altering the server’s enclosure in any way other than the installation operations specified in this document may invalidate the server’s safety certifications.

CAUTION: Never pile books, papers, or other objects on the chassis, drop it, or subject it to pressure in any other way. The internal circuits can be damaged, and the battery may be crushed or punctured. Besides irreparable damage to the unit, the result could be dangerous heat and even fire.

CAUTION: There are no user-serviceable components inside the chassis. The chassis should only be opened by qualified service personnel. Never disassemble, tamper with, or attempt to repair the server. Doing so may cause smoke, fire, electri- cal shock, serious physical injury, or death.

WARNING: In HL servers, multiple sources of supply exist. Be sure to discon- nect all sources before servicing.

•Do not insert objects through openings in the chassis. Doing so could result in a short circuit that might cause a fire or an electrical shock.

•Do not operate the server in an explosive atmosphere, in the presence of flammable gases.

•To ensure proper cooling, always operate the server with its covers in place. Do not block any openings on the chassis. Do not place the server near a heater.

•Always exit the software application properly before turning off the server to ensure data integrity.

16	8e6 Enterprise Reporter Quick Start Guide

Image 20

Contents Guide 8e6 Enterprise Reporter Quick Start Guide Contents Index Regulatory Specifications and DisclaimersAppendix Scsi Connected Storage Device ER Enterprise Reporter Introduction About this Document Conventions Used in this Document8e6 Taiwan Procedures8e6 Corporate Headquarters USA Unpack the Unit from the Carton Select a Site for the Server Rack Setup Precautions Rack Mount the ServerRack Setup Suggestions Install the Inner RailsInstall the Outer Rails Rack Mount Instructions for HL Servers8e6 Enterprise Reporter Quick Start Guide Install the Server into the Rack Install the Server into a Telco Rack Rack Mount Instructions for SL Servers Install the Inner SlidesInstall the Outer Slides Install the Slide Assemblies to the Rack Install the Chassis into the Rack Install the SL or HL Server Bezel Front of bezelCheck the Power Supply Power Supply PrecautionsGeneral Safety Information Server Operation and Maintenance PrecautionsAC Power Cord and Cable Precautions Electrical Safety PrecautionsMotherboard Battery Precautions Setup Procedures Quick Start Setup RequirementsAdministrator Console Setup Requirements LCD Panel Setup RequirementsQuick Start Setup Procedures Storage Device Setup for Attached Storage UnitsMonitor and Keyboard Setup Serial Console SetupDiagram of SL chassis front panel, power button at far right HyperTerminal Setup Procedures 8e6 Enterprise Reporter Quick Start Guide 8e6 Enterprise Reporter Quick Start Guide Login screen Quick Start menu screenQuick Start menu administration menu System Status screen Log Off, Disconnect the PeripheralsWorkstation Configurations Console Setup ProceduresPreliminary Setup Left Boot Up Process Log in to the Administrator Console Network SetupAccess the Internet Network Settings 8e6 Enterprise Reporter Quick Start Guide Regional Setting Time Zone Regional Setting Language Regional Setting NTP ServersPhysically Connect the ER to the Network 8e6 menu LCD Panel Setup ProceduresLCD Menu Current Patch Level LAN 1 Link StatusGateway DNS 1Regional Setting Time Zone, date, time Host NameReset Admin Console Password RebootLCD Options menu ShutdownLCD Controls HeartbeatBacklight Change User Name and Password, Set Self- Monitoring Access the InternetChange User Name and Password Enter a User Name and PasswordEnter the Master Administrator’s E-Mail Address Set Self-MonitoringR3000 Configuration Select 8e6 Enterprise Reporter, and then click SaveClient Workstation Configuration Launch the ER Client Enter the Password, and Confirm Password Conclusion Administrator Console, Expiration Screen ER Client, ER Server Statistics Window SL Unit LED Indicator KeyLED Indicator Color Condition Description HL Unit Rear LED Indicators for Hardware Status Monitoring HL and SL Units RAIDSafety Compliance Declaration of the Manufacturer or ImporterElectromagnetic Compatibility EMC Models HL-022-002, HL-002-002, SL-002-002Electromagnetic Compatibility Class a Notice EC Declaration of Conformity Unpack the Unit from the Carton Preliminary Setup ProceduresOther Required Installation Items Rack Mount Components Rack Setup PrecautionsRack Mount the Server Step Step Step Install the Unit Link the ER Unit with the Scsi Connected DeviceRestart the Storage Device Unit Shut Down, Restart ProceduresShut Down the Storage Device Unit Physical Components LED Display Temperature and Ventilation StatusPower Supply Status Management Alarm Disc Drive AlarmSilence Button Disk Drive ActivityIndex 8e6 Enterprise Reporter Quick Start Guide