Avaya S8700 manual Adding media gateways, Cabinet Cabinet Description

Page 52

Chapter 5: IP interface translations

Adding media gateways

Note:

If system translations have been loaded on the server, media gateways do not need to be added to administer the IPSI.

1.Type add cabinet n and press Enter, where n is the cabinet number, for each stack of media gateways that is controlled by one TN2312BP IPSI circuit pack.

A cabinet is defined as a group of up to five G650 Media Gateways that are mounted in a rack and TDM-connected.

2.Fill in the carrier location letter and the carrier type for each media gateway in the cabinet.

add cabinet 1			CABINET		Page 1 of 1
CABINET DESCRIPTION			CABINET
CABINET DESCRIPTION		1
	Cabinet:	1
	Cabinet Layout:	G650-rack-mount-stack
	Cabinet Type: expansion-portnetwork
Number of Portnetworks: 1
Survivable Remote EPN? n			IP Network Region:1
	Location: 1		IP Network Region:1
Cabinet Holdover: A-carrier-only					Building:
	Room:			Floor:	Building:
CARRIER DESCRIPTION			Number
Carrier	Carrier Type		Number
E	not-used		PN	09
D	not-used		PN	09
C	not-used		PN	09
B	G650-port		PN	09
A	G650-port		PN	09

52 Installing and Configuring the Avaya S8700-Series Server

January 2008

Image 52

Contents Installing and Configuring the Avaya S8700-Series Server ReleaseAvaya Inc All Rights Reserved Introduction Server configuration Postinstallation administration Index 101 Introduction AudienceHow to use Avaya installation documents Pre-installation requirements Preinstallation tasks to complete at the customer sitePNC license settings for S8700-series Servers Verifying that all the required equipment is on siteEnsuring that the preinstallation tasks are complete Equipment specificationsShows specifications for the S8710, S8720 and S8730 Servers Introduction About RAID About S8730 Server configurationsAbout server port connections S8700-series port connections Figure notes H3df87h2 LAO Hw8730s2 LAO H3df87s2 LAO Connecting to separated servers Connecting to collocated serversAbout modem connections About Processor Ethernet About media gatewaysModem options About software duplication About SSHIntroduction Snmp configuration Configuring the Snmp modules in the UPSDefault UPS IP addresses for S8700-series Servers Single control Duplicated control Network CNA Network CNBPrerequisites for configuring the Snmp module Security AlertAdministering the Snmp modules Setting selected traps alarmingDefault IP addresses for the Ethernet switch Preparing to configure the Ethernet switch Configuring the Ethernet switch Snmp configuration Communication Manager installation Clearing the ARP cache on the laptopAccessing the server Applying power to the serverConfiguring Telnet for Windows 2000 and Windows XP Installing Avaya Communication Manager Page Server configuration Creating a super-user login Opening the Maintenance Web InterfaceCopying files to the server Configuring the server manually Methods of Configuring a serverSelect type of authentication section Choose Password Maintenance Web Pages configuration screens Methods of Configuring a server Performing the manual configuration S8700-series Server Ethernet assignmentsControl network a Eth0 Eth2 Control network B Eth3 if used Eth4 Eth0 Eth2 Duplication LinkAvaya Installation Wizard About the Avaya Installation WizardClick Launch Avaya Installation Wizard Click Execute PingConfiguring the modem Select Change Modem Setting and click ContinueConfiguring memory for an S8720 Server Select either Standard or Extra Large Ensuring ESS and LSP compatibilityClick Close Window Enabling firewall settings Enabling network time serversConfiguring the NIC Configuring a second server Accessing the standby serverRelease the server Interchanging serversPerforming an integrity check on the active server Interchanging serversClick Interchange Page IP interface translations Inputting initial system translationsAdding media gateways Cabinet Cabinet DescriptionSet the Ipsi Control of Port Networks field to enabled Enabling the IpsiAdding the Ipsi to the system Type add ipserver-interface PNnumber and press EnterSetting the alarm activation level Enter y in the Enable Operation of Ipsi Duplication fieldEnabling Ipsi duplication duplicated control network only Saving translationsPage Connecting to the IPSIs IP interface configurationIpsi address configuration Programming the Ipsi for static addressing Connecting the laptop directly to the Ipsi Type show control interface and press Enter Setting the Vlan and diffserv parameters Programming the Ipsi for Dhcp addressing Ipsi LED display for static addressCLK CLK Verifying connectivity to the server Verifying that the IPSIs are translatedUpgrading the Ipsi firmware version if necessary Enabling control of the IPSIsVerifying the license status Postinstallation administration Verifying translationsSetting rules for daylight savings time Type change daylight-savings-rules and press EnterSetting locations if necessary Type change locations and press EnterVerifying the date and the time main server only Clearing and resolving alarms Enabling and disabling the Ethernet switch portsEnabling alarms to Inads by way of a modem Click Submit ChangesEnabling alarms to Inads by way of the Snmp module Backing up files to the compact flash mediaBefore leaving the site Testing the Ipsi circuit pack Installation verificationTesting the license file S8730 LEDs LEDs on the front panel of the S8730 ServerS8710 and S8720 LEDs LEDs on the back panel of the S8730 ServerLEDs on the front panel of the S8710 and the S8720 Servers Additional server LED information LEDs on the back panel of the S8710 and the S8720 ServersAvaya C360 Ethernet switch LEDs LAGLEDs on the Powerware 9125 UPS UPS LEDsTN2312BP Ipsi LEDs TN2312BP Ipsi circuit pack faceplate Ipsi LED display for a static IP address Ipsi services port Connectivity statusPage Appendix a Server access Accessing the command line interface of the server withBackspace key area, select Control-H Connecting to the server directly Ca873srv LAO Cadlsrv2 KLC Connecting to the server remotely over the network Connecting to the server remotely over a modemAccessing the Maintenance Web Interface Finding the IP address of the active serverClick Launch Maintenance Web Interface Using the SAT command line promptType of connection Procedure Configuring the network for Windows 2000 and XP Logins for Avaya technicians and BusinessPartnersSelect Internet Protocol TCP/IP Setting the browser options for Internet Explorer Click on LAN settings, then AdvancedTroubleshooting the installation of the server hardware Appendix B Installation troubleshootingProblem Possible solution Troubleshooting the configuration of the server hardware Ping 192.11.13.6 and press EnterPress Enter Problem Possible solution Index NumericalIpsi Preparing to configure

Related manuals

Manual 20 pages 56.84 Kb

Manual 20 pages 18.09 Kb

Manual 8 pages 16.6 Kb