Avaya S8700 manual TN2312BP Ipsi LEDs

Page 82

Chapter 8: Installation verification

TN2312BP IPSI LEDs

TN2312BP IP Server Interface (IPSI) circuit pack LEDs include:

●Standard LEDs and connector slots (Figure 12: TN2312BP IPSI circuit pack faceplate on page 83)

●A programmable LED display, which indicates:

-The type of IPSI IP address. For a dynamic address, the display shows media gateway the location of the media gateway. For a static address, the display shows I P. (Figure 13: IPSI LED display for a static IP address on page 84)

-Connectivity

82 Installing and Configuring the Avaya S8700-Series Server

January 2008

Image 82

Contents Installing and Configuring the Avaya S8700-Series Server ReleaseAvaya Inc All Rights Reserved Introduction Server configuration Postinstallation administration Index 101 Introduction AudienceHow to use Avaya installation documents PNC license settings for S8700-series Servers Pre-installation requirementsPreinstallation tasks to complete at the customer site Verifying that all the required equipment is on siteEnsuring that the preinstallation tasks are complete Equipment specificationsShows specifications for the S8710, S8720 and S8730 Servers Introduction About RAID About S8730 Server configurationsAbout server port connections S8700-series port connections Figure notes H3df87h2 LAO Hw8730s2 LAO H3df87s2 LAO Connecting to separated servers Connecting to collocated serversAbout modem connections About Processor Ethernet About media gatewaysModem options About software duplication About SSHIntroduction Snmp configuration Configuring the Snmp modules in the UPSDefault UPS IP addresses for S8700-series Servers Single control Duplicated control Network CNA Network CNBPrerequisites for configuring the Snmp module Security AlertAdministering the Snmp modules Setting selected traps alarmingDefault IP addresses for the Ethernet switch Preparing to configure the Ethernet switch Configuring the Ethernet switch Snmp configuration Communication Manager installation Clearing the ARP cache on the laptopAccessing the server Applying power to the serverConfiguring Telnet for Windows 2000 and Windows XP Installing Avaya Communication Manager Page Server configuration Creating a super-user login Opening the Maintenance Web InterfaceCopying files to the server Configuring the server manually Methods of Configuring a serverSelect type of authentication section Choose Password Maintenance Web Pages configuration screens Methods of Configuring a server Control network a Eth0 Eth2 Control network B Eth3 if used Performing the manual configurationS8700-series Server Ethernet assignments Eth4 Eth0 Eth2 Duplication LinkAvaya Installation Wizard About the Avaya Installation WizardClick Launch Avaya Installation Wizard Click Execute PingConfiguring the modem Select Change Modem Setting and click ContinueConfiguring memory for an S8720 Server Select either Standard or Extra Large Ensuring ESS and LSP compatibilityClick Close Window Enabling firewall settings Enabling network time serversConfiguring the NIC Release the server Configuring a second serverAccessing the standby server Interchanging serversPerforming an integrity check on the active server Interchanging serversClick Interchange Page IP interface translations Inputting initial system translationsAdding media gateways Cabinet Cabinet DescriptionSet the Ipsi Control of Port Networks field to enabled Enabling the IpsiAdding the Ipsi to the system Type add ipserver-interface PNnumber and press EnterEnabling Ipsi duplication duplicated control network only Setting the alarm activation levelEnter y in the Enable Operation of Ipsi Duplication field Saving translationsPage Connecting to the IPSIs IP interface configurationIpsi address configuration Programming the Ipsi for static addressing Connecting the laptop directly to the Ipsi Type show control interface and press Enter Setting the Vlan and diffserv parameters Programming the Ipsi for Dhcp addressing Ipsi LED display for static addressCLK CLK Upgrading the Ipsi firmware version if necessary Verifying connectivity to the serverVerifying that the IPSIs are translated Enabling control of the IPSIsVerifying the license status Postinstallation administration Verifying translationsSetting rules for daylight savings time Type change daylight-savings-rules and press EnterSetting locations if necessary Type change locations and press EnterVerifying the date and the time main server only Clearing and resolving alarms Enabling and disabling the Ethernet switch portsEnabling alarms to Inads by way of a modem Click Submit ChangesEnabling alarms to Inads by way of the Snmp module Backing up files to the compact flash mediaBefore leaving the site Testing the Ipsi circuit pack Installation verificationTesting the license file S8730 LEDs LEDs on the front panel of the S8730 ServerS8710 and S8720 LEDs LEDs on the back panel of the S8730 ServerLEDs on the front panel of the S8710 and the S8720 Servers Additional server LED information LEDs on the back panel of the S8710 and the S8720 ServersAvaya C360 Ethernet switch LEDs LAGLEDs on the Powerware 9125 UPS UPS LEDsTN2312BP Ipsi LEDs TN2312BP Ipsi circuit pack faceplate Ipsi LED display for a static IP address Ipsi services port Connectivity statusPage Appendix a Server access Accessing the command line interface of the server withBackspace key area, select Control-H Connecting to the server directly Ca873srv LAO Cadlsrv2 KLC Connecting to the server remotely over the network Connecting to the server remotely over a modemAccessing the Maintenance Web Interface Finding the IP address of the active serverClick Launch Maintenance Web Interface Using the SAT command line promptType of connection Procedure Configuring the network for Windows 2000 and XP Logins for Avaya technicians and BusinessPartnersSelect Internet Protocol TCP/IP Setting the browser options for Internet Explorer Click on LAN settings, then AdvancedTroubleshooting the installation of the server hardware Appendix B Installation troubleshootingProblem Possible solution Troubleshooting the configuration of the server hardware Ping 192.11.13.6 and press EnterPress Enter Problem Possible solution Index NumericalIpsi Preparing to configure

Related manuals

Manual 20 pages 56.84 Kb

Manual 20 pages 18.09 Kb

Manual 8 pages 16.6 Kb