Lathem PC3500TX manual Setup Mode - 177B Firmware For PayClock Pro 3.355G and earlier

Page 13

Setup Mode – 177B Firmware (For PayClock Pro 3.355G and earlier)

PC3500TX Terminal Installation & User’s Guide - 9

Setup Mode – 177B Firmware (For PayClock Pro 3.355G and earlier)

To Setup the PC3500TX’s Ethernet Communications

Setup Mode allows you to setup the terminal to communicate through the network with the PayClock “TCP/IP Server”.

IMPORTANT! The PC3500TX terminal requires that the Terminal Manager module runs with “TCP/IP Server” enabled.

♦Locate the Test/Use switch on the back of the terminal.

♦Slide the switch into the TEST position (away from the modular jacks).

♦With the “TEST MODE” message in the terminal display, press the CLEAR key five

(5) times. The message “RESTART MODE” appears on the top line of the display. Press the ENTER key three (3) times to clear all memory prior to setting up the terminal. After resetting, the terminal will again display “TEST MODE”.

NOTE: Skipping this step greatly increases the chances of unreliable test results during the setup of the terminal.

♦Press the CLEAR key one (1) time.

The terminal displays “SETUP MODE” on the top line followed by: TERM 000.000.000.000 displayed for one (1) second

HOST 000.000.000.000 displayed for one (1) second

GATE 000.000.000.000 displayed for one (1) second

(This message will only display if the gate address was previously setup) MASK 000.000.000.000 displayed for one (1) second

NOTE: The above sequence will repeat itself until either the CLEAR or ENTER key is pressed. Pressing the CLEAR key will bypass the Setup Mode. Pressing the ENTER key will enable the Setup Mode.

Image 13

Contents Installation & User’s Guide PC3500TX TerminalLimited One-Year Limited Warranty PayClock, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names INSTALL/REPLACE THE OPTIONAL BACKUP BATTERY SETUP THE TERMINALOPTIONAL SIGNAL DEVICE NETWORK WIRING TOPOLOGIESWelcome Features and SpecificationsC H A P T E R PC3500TX NOTICE - For Firmware 177B and EarlierNote about Lithium Battery Power Surges and SpikesMounting the Terminal Pre-Terminal InstallationMount the Terminal To install the mounting bracket Turn the key clockwise to lock the terminal in place Connect the Communication Cable Starting the Test and Setup Mode Setup the TerminalSubnet Mask Network Test Not Used8 - PC3500TX Terminal Installation & User’s Guide To power up the terminalPlug the terminal 12VDC power supply into the power connector To Setup the PC3500TX’s Ethernet Communications Setup Mode - 177B Firmware For PayClock Pro 3.355G and earlierTERMINAL IP ADDRESS ###. ###. ###. ### HIT ENTER IF DEFAULT ROUTE REQUIREDHOST IP ADDRESS ###. ###. ###. ### NETWORK MASK ###. ###. ###. ###ENETADD=XXXXXXXXXXXX SETUP COMPLETE Enet MAC Address XXXXXXXXXXXX Setup Mode - 177G Firmware For PayClock Pro 4.1 and laterTCP/IP Conn. Type TCP/IP Conn. Mode Default Router?Enter Socket Port # Enter Terminal IP ###. ###. ###. ###Enter Keepalive Mode Enter Sub Net Mask ###. ###. ###. ###To start the Test Mode Test Mode“TEST MODE” PROG# TEST MODE 128 YYBATTERY TEST PASS ENTER TO RETEST Battery TestNote If you do not have a battery installed, the test will fail SWITCH TEST SWITCH TO USE POSITIONRestart Mode Unlocking Your Terminal Through Terminal ManagerTo restart the terminal PRESS ENTER TO CLEAR ALL TRANSACTION DATATo punch Use the TerminalTo start a New Day To transferTo enter amounts To review your last punchWhen you see ENTER ASSOCIATES BADGE, swipe the employee’s badge When you see BADGE FOR SUPERVISOR OVERIDE, swipe your badgeSupervisor Functions To see employee InfoA P P E N D I X A Install/Replace the Optional Backup BatteryGENERAL SPECIFICATIONS Optional Signal DeviceTo connect your signaling devices A P P E N D I X BTypical Lan network configuration Network Wiring TopologiesA P P E N D I X C 24 - PC3500TX Terminal Installation & User’s Guide Typical Wan network configurationTroubleshooting the Terminal Problem The terminal is not communicating with the computer 26 - PC3500TX Terminal Installation & User’s GuideProblem A previously working terminal now is not operational Reason TEST/USE switch is not in the Use positionReason Bar code badge is not manufactured to specifications Problem The terminal does not accept badge dataSolution Refer to vendor’s manufacturing specifications Solution Ensure the badge stripe faces away from the keypadSolution Open the PC3500TX’s Terminal Properties in Terminal Manager 28 - PC3500TX Terminal Installation & User’s GuideClick OK to save the changes Update the terminal with the changes Select the Advanced tabA P P E N D I X D Terminal Data Sheet