Lathem PC3500TX manual To start the Test Mode, “Test Mode” Prog#, TEST MODE 128 YY

Page 19

PC3500TX Terminal Installation & User’s Guide - 15

Test Mode

Use the Test Mode to make sure the keypad, memory; real time terminal, and badge reader are working.

NOTE: You can exit Test Mode at any time by placing the Test/Use switch back to the USE position (toward the modular jacks), then pressing the Clear key.

To start the Test Mode

♦Locate the Test/Use switch on the back of the terminal.

♦Slide the switch into the TEST position (away from the modular jacks). The terminal displays.

“TEST MODE”

PROG# XXX

♦Press the Enter key to go into Test Mode.

TEST MODE (128) (YY)

- - - - - - - - - - - - - - - - - - - - - - - - - -

The terminal displays “TEST MODE” on the top line followed by two sets of numbers. The first number shows the amount of memory installed (in kilobytes). The scrolling numbers on the right (YY) show the terminal Real Time Terminal advancing in seconds (00-59).

Now you can test the keypad and badge reader.

To Test the Keypad

♦When you press a key, the terminal beeps and displays the key value on the 2nd line.

♦Press Enter to see

KEY INPUT ACCEPTED

To Test the Badge Reader

Test Mode accepts swipes from the badge reader. To test the reader, swipe a badge. The terminal beeps and displays the badge data.

♦Swipe a badge through the slot reader.

Image 19

Contents Installation & User’s Guide PC3500TX TerminalLimited One-Year Limited Warranty PayClock, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names NETWORK WIRING TOPOLOGIES SETUP THE TERMINALINSTALL/REPLACE THE OPTIONAL BACKUP BATTERY OPTIONAL SIGNAL DEVICEPC3500TX NOTICE - For Firmware 177B and Earlier Features and SpecificationsWelcome C H A P T E RNote about Lithium Battery Power Surges and SpikesMounting the Terminal Pre-Terminal InstallationMount the Terminal To install the mounting bracket Turn the key clockwise to lock the terminal in place Connect the Communication Cable Network Test Not Used Setup the TerminalStarting the Test and Setup Mode Subnet Mask8 - PC3500TX Terminal Installation & User’s Guide To power up the terminalPlug the terminal 12VDC power supply into the power connector To Setup the PC3500TX’s Ethernet Communications Setup Mode - 177B Firmware For PayClock Pro 3.355G and earlierNETWORK MASK ###. ###. ###. ### HIT ENTER IF DEFAULT ROUTE REQUIREDTERMINAL IP ADDRESS ###. ###. ###. ### HOST IP ADDRESS ###. ###. ###. ###ENETADD=XXXXXXXXXXXX SETUP COMPLETE Enet MAC Address XXXXXXXXXXXX Setup Mode - 177G Firmware For PayClock Pro 4.1 and laterTCP/IP Conn. Type Enter Terminal IP ###. ###. ###. ### Default Router?TCP/IP Conn. Mode Enter Socket Port #Enter Keepalive Mode Enter Sub Net Mask ###. ###. ###. ###TEST MODE 128 YY Test ModeTo start the Test Mode “TEST MODE” PROG#SWITCH TEST SWITCH TO USE POSITION Battery TestBATTERY TEST PASS ENTER TO RETEST Note If you do not have a battery installed, the test will failPRESS ENTER TO CLEAR ALL TRANSACTION DATA Unlocking Your Terminal Through Terminal ManagerRestart Mode To restart the terminalTo punch Use the TerminalTo review your last punch To transferTo start a New Day To enter amountsTo see employee Info When you see BADGE FOR SUPERVISOR OVERIDE, swipe your badgeWhen you see ENTER ASSOCIATES BADGE, swipe the employee’s badge Supervisor FunctionsA P P E N D I X A Install/Replace the Optional Backup BatteryA P P E N D I X B Optional Signal DeviceGENERAL SPECIFICATIONS To connect your signaling devicesTypical Lan network configuration Network Wiring TopologiesA P P E N D I X C 24 - PC3500TX Terminal Installation & User’s Guide Typical Wan network configurationTroubleshooting the Terminal Reason TEST/USE switch is not in the Use position 26 - PC3500TX Terminal Installation & User’s GuideProblem The terminal is not communicating with the computer Problem A previously working terminal now is not operationalSolution Ensure the badge stripe faces away from the keypad Problem The terminal does not accept badge dataReason Bar code badge is not manufactured to specifications Solution Refer to vendor’s manufacturing specificationsSelect the Advanced tab 28 - PC3500TX Terminal Installation & User’s GuideSolution Open the PC3500TX’s Terminal Properties in Terminal Manager Click OK to save the changes Update the terminal with the changesA P P E N D I X D Terminal Data Sheet