Lathem PC3500TX manual

Page 3

PayClock, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names

mentioned in this manual may be trademarks of their respective companies and are hereby acknowledged.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTICE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructional manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense.

Image 3

Contents Installation & User’s Guide PC3500TX TerminalLimited One-Year Limited Warranty PayClock, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names NETWORK WIRING TOPOLOGIES SETUP THE TERMINALINSTALL/REPLACE THE OPTIONAL BACKUP BATTERY OPTIONAL SIGNAL DEVICEPC3500TX NOTICE - For Firmware 177B and Earlier Features and SpecificationsWelcome C H A P T E RNote about Lithium Battery Power Surges and SpikesPre-Terminal Installation Mounting the TerminalMount the Terminal To install the mounting bracket Turn the key clockwise to lock the terminal in place Connect the Communication Cable Network Test Not Used Setup the TerminalStarting the Test and Setup Mode Subnet MaskTo power up the terminal 8 - PC3500TX Terminal Installation & User’s GuidePlug the terminal 12VDC power supply into the power connector To Setup the PC3500TX’s Ethernet Communications Setup Mode - 177B Firmware For PayClock Pro 3.355G and earlierNETWORK MASK ###. ###. ###. ### HIT ENTER IF DEFAULT ROUTE REQUIREDTERMINAL IP ADDRESS ###. ###. ###. ### HOST IP ADDRESS ###. ###. ###. ###ENETADD=XXXXXXXXXXXX SETUP COMPLETE Setup Mode - 177G Firmware For PayClock Pro 4.1 and later Enet MAC Address XXXXXXXXXXXXTCP/IP Conn. Type Enter Terminal IP ###. ###. ###. ### Default Router?TCP/IP Conn. Mode Enter Socket Port #Enter Keepalive Mode Enter Sub Net Mask ###. ###. ###. ###TEST MODE 128 YY Test ModeTo start the Test Mode “TEST MODE” PROG#SWITCH TEST SWITCH TO USE POSITION Battery TestBATTERY TEST PASS ENTER TO RETEST Note If you do not have a battery installed, the test will failPRESS ENTER TO CLEAR ALL TRANSACTION DATA Unlocking Your Terminal Through Terminal ManagerRestart Mode To restart the terminalTo punch Use the TerminalTo review your last punch To transferTo start a New Day To enter amountsTo see employee Info When you see BADGE FOR SUPERVISOR OVERIDE, swipe your badgeWhen you see ENTER ASSOCIATES BADGE, swipe the employee’s badge Supervisor FunctionsA P P E N D I X A Install/Replace the Optional Backup BatteryA P P E N D I X B Optional Signal DeviceGENERAL SPECIFICATIONS To connect your signaling devicesNetwork Wiring Topologies Typical Lan network configurationA P P E N D I X C 24 - PC3500TX Terminal Installation & User’s Guide Typical Wan network configurationTroubleshooting the Terminal Reason TEST/USE switch is not in the Use position 26 - PC3500TX Terminal Installation & User’s GuideProblem The terminal is not communicating with the computer Problem A previously working terminal now is not operationalSolution Ensure the badge stripe faces away from the keypad Problem The terminal does not accept badge dataReason Bar code badge is not manufactured to specifications Solution Refer to vendor’s manufacturing specificationsSelect the Advanced tab 28 - PC3500TX Terminal Installation & User’s GuideSolution Open the PC3500TX’s Terminal Properties in Terminal Manager Click OK to save the changes Update the terminal with the changesA P P E N D I X D Terminal Data Sheet