Lathem PC3500TX manual Enetadd=Xxxxxxxxxxxx Setup Complete

Page 15

PC3500TX Terminal Installation & User’s Guide - 11

This is the system Router used for directing network traffic. (See your network administrator for assignment.)

Enter the numeric Router or Gateway address in blocks of three followed by the ENTER key.

The following message will be displayed:

ENETADD=XXXXXXXXXXXX

SETUP COMPLETE

The XXXXXXXXXXXX represents the unique Ethernet address programmed into the EPROM by the factory. (Also known as the MAC Address)

Important: Write this number down on the Terminal Data Sheet and on the Terminal sticker. This number is unique to each Terminal and may be needed for future troubleshooting.

To exit the Setup Mode, place the TEST/USE switch to the USE position and press the CLEAR key. The terminal will goes through its power up sequence. The terminal displays: “TERMINAL LOCKED”. The terminal can now accept a download.

Image 15

Contents Installation & User’s Guide PC3500TX TerminalLimited One-Year Limited Warranty PayClock, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names NETWORK WIRING TOPOLOGIES SETUP THE TERMINALINSTALL/REPLACE THE OPTIONAL BACKUP BATTERY OPTIONAL SIGNAL DEVICEPC3500TX NOTICE - For Firmware 177B and Earlier Features and SpecificationsWelcome C H A P T E RNote about Lithium Battery Power Surges and SpikesPre-Terminal Installation Mounting the TerminalMount the Terminal To install the mounting bracket Turn the key clockwise to lock the terminal in place Connect the Communication Cable Network Test Not Used Setup the TerminalStarting the Test and Setup Mode Subnet MaskTo power up the terminal 8 - PC3500TX Terminal Installation & User’s GuidePlug the terminal 12VDC power supply into the power connector To Setup the PC3500TX’s Ethernet Communications Setup Mode - 177B Firmware For PayClock Pro 3.355G and earlierNETWORK MASK ###. ###. ###. ### HIT ENTER IF DEFAULT ROUTE REQUIREDTERMINAL IP ADDRESS ###. ###. ###. ### HOST IP ADDRESS ###. ###. ###. ###ENETADD=XXXXXXXXXXXX SETUP COMPLETE Setup Mode - 177G Firmware For PayClock Pro 4.1 and later Enet MAC Address XXXXXXXXXXXXTCP/IP Conn. Type Enter Terminal IP ###. ###. ###. ### Default Router?TCP/IP Conn. Mode Enter Socket Port #Enter Keepalive Mode Enter Sub Net Mask ###. ###. ###. ###TEST MODE 128 YY Test ModeTo start the Test Mode “TEST MODE” PROG#SWITCH TEST SWITCH TO USE POSITION Battery TestBATTERY TEST PASS ENTER TO RETEST Note If you do not have a battery installed, the test will failPRESS ENTER TO CLEAR ALL TRANSACTION DATA Unlocking Your Terminal Through Terminal ManagerRestart Mode To restart the terminalTo punch Use the TerminalTo review your last punch To transferTo start a New Day To enter amountsTo see employee Info When you see BADGE FOR SUPERVISOR OVERIDE, swipe your badgeWhen you see ENTER ASSOCIATES BADGE, swipe the employee’s badge Supervisor FunctionsA P P E N D I X A Install/Replace the Optional Backup BatteryA P P E N D I X B Optional Signal DeviceGENERAL SPECIFICATIONS To connect your signaling devicesNetwork Wiring Topologies Typical Lan network configurationA P P E N D I X C 24 - PC3500TX Terminal Installation & User’s Guide Typical Wan network configurationTroubleshooting the Terminal Reason TEST/USE switch is not in the Use position 26 - PC3500TX Terminal Installation & User’s GuideProblem The terminal is not communicating with the computer Problem A previously working terminal now is not operationalSolution Ensure the badge stripe faces away from the keypad Problem The terminal does not accept badge dataReason Bar code badge is not manufactured to specifications Solution Refer to vendor’s manufacturing specificationsSelect the Advanced tab 28 - PC3500TX Terminal Installation & User’s GuideSolution Open the PC3500TX’s Terminal Properties in Terminal Manager Click OK to save the changes Update the terminal with the changesA P P E N D I X D Terminal Data Sheet