Lathem PC3500TX Setup Mode - 177G Firmware For PayClock Pro 4.1 and later, TCP/IP Conn. Type

Page 16

Setup Mode – 177G Firmware (For PayClock Pro 4.1 and later)

12 - PC3500TX Terminal Installation & User’s Guide

Setup Mode – 177G Firmware (For PayClock Pro 4.1 and later)

To Setup the PC3500TX’s Ethernet Communications

Setup Mode allows you to setup the terminal to communicate through the network with the PayClock “TCP/IP Server”.

IMPORTANT! The PC3500TX terminal requires that the Terminal Manager module runs with “TCP/IP Server” enabled.

♦Locate the Test/Use switch on the back of the terminal.

♦Slide the switch into the TEST position (away from the modular jacks).

♦With the “TEST MODE” message in the terminal display, press the CLEAR key five

(5) times. The message “RESTART MODE” appears on the top line of the display. Press the ENTER key three (3) times to clear all memory prior to setting up the terminal. After resetting the terminal will again display “TEST MODE”.

NOTE: Skipping this step greatly increases the chances of unreliable test results during the setup of the terminal.

♦Press the CLEAR key one (1) time. The terminal displays “SETUP MODE”. Press the ENTER key. The following message will be displayed:

Enet MAC Address:

XXXXXXXXXXXX

Note: This screen is view only.

Press the ENTER key. The following message will be displayed:

TCP/IP Conn. Type

Press the CLEAR key and select the Client option.

Image 16

Contents PC3500TX Terminal Installation & User’s GuideLimited One-Year Limited Warranty PayClock, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names SETUP THE TERMINAL INSTALL/REPLACE THE OPTIONAL BACKUP BATTERYOPTIONAL SIGNAL DEVICE NETWORK WIRING TOPOLOGIESFeatures and Specifications WelcomeC H A P T E R PC3500TX NOTICE - For Firmware 177B and EarlierPower Surges and Spikes Note about Lithium BatteryMounting the Terminal Pre-Terminal InstallationMount the Terminal To install the mounting bracket Turn the key clockwise to lock the terminal in place Connect the Communication Cable Setup the Terminal Starting the Test and Setup ModeSubnet Mask Network Test Not Used8 - PC3500TX Terminal Installation & User’s Guide To power up the terminalPlug the terminal 12VDC power supply into the power connector Setup Mode - 177B Firmware For PayClock Pro 3.355G and earlier To Setup the PC3500TX’s Ethernet CommunicationsHIT ENTER IF DEFAULT ROUTE REQUIRED TERMINAL IP ADDRESS ###. ###. ###. ###HOST IP ADDRESS ###. ###. ###. ### NETWORK MASK ###. ###. ###. ###ENETADD=XXXXXXXXXXXX SETUP COMPLETE Enet MAC Address XXXXXXXXXXXX Setup Mode - 177G Firmware For PayClock Pro 4.1 and laterTCP/IP Conn. Type Default Router? TCP/IP Conn. ModeEnter Socket Port # Enter Terminal IP ###. ###. ###. ###Enter Sub Net Mask ###. ###. ###. ### Enter Keepalive ModeTest Mode To start the Test Mode“TEST MODE” PROG# TEST MODE 128 YYBattery Test BATTERY TEST PASS ENTER TO RETESTNote If you do not have a battery installed, the test will fail SWITCH TEST SWITCH TO USE POSITIONUnlocking Your Terminal Through Terminal Manager Restart ModeTo restart the terminal PRESS ENTER TO CLEAR ALL TRANSACTION DATAUse the Terminal To punchTo transfer To start a New DayTo enter amounts To review your last punchWhen you see BADGE FOR SUPERVISOR OVERIDE, swipe your badge When you see ENTER ASSOCIATES BADGE, swipe the employee’s badgeSupervisor Functions To see employee InfoInstall/Replace the Optional Backup Battery A P P E N D I X AOptional Signal Device GENERAL SPECIFICATIONSTo connect your signaling devices A P P E N D I X BTypical Lan network configuration Network Wiring TopologiesA P P E N D I X C Typical Wan network configuration 24 - PC3500TX Terminal Installation & User’s GuideTroubleshooting the Terminal 26 - PC3500TX Terminal Installation & User’s Guide Problem The terminal is not communicating with the computerProblem A previously working terminal now is not operational Reason TEST/USE switch is not in the Use positionProblem The terminal does not accept badge data Reason Bar code badge is not manufactured to specificationsSolution Refer to vendor’s manufacturing specifications Solution Ensure the badge stripe faces away from the keypad28 - PC3500TX Terminal Installation & User’s Guide Solution Open the PC3500TX’s Terminal Properties in Terminal ManagerClick OK to save the changes Update the terminal with the changes Select the Advanced tabTerminal Data Sheet A P P E N D I X D