Lathem PC3500TX manual Battery Test Pass Enter To Retest, To start the DI-DO Test

Page 20

16 - PC3500TX Terminal Installation & User’s Guide

♦If the terminal accepts the badge, the badge number displays and the terminal beeps.

To continue in the TEST MODE, press the CLEAR key three (3) times. You will then see Battery Test.

Battery Test

If you purchased the optional battery (UPS), you can use the Battery Test to check the battery. To start this test, press Enter when you see “BATTERY TEST”. You will then see.

BATTERY TEST PASS

ENTER TO RETEST

Note: If you do not have a battery installed, the test will fail.

Press Clear to go to the DI-DO Test.

DI-DO Test

If you have installed a bell relay, you can use the DI-DO Test to check the terminal’s DATA IN/DATA OUT port where the relay connects to the terminal.

To start the DI-DO Test

♦Press Enter when you see “DI-DO TEST”. You will then see

SWITCH TEST SWITCH

TO USE POSITION

♦Place the Test switch into the USE position. Since your terminal does not have a loop back jumper, you will see

DI-DO TEST FAILED

ENTER TO RETEST

♦Place the Test/Use switch back into the TEST position. This provides the terminal with its own loop back jumper

♦Press Enter. You will see

DI-DO TEST PASSED

ENTER TO RETEST

Press Clear to go to Restart Mode

Image 20

Contents PC3500TX Terminal Installation & User’s GuideLimited One-Year Limited Warranty PayClock, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names SETUP THE TERMINAL INSTALL/REPLACE THE OPTIONAL BACKUP BATTERYOPTIONAL SIGNAL DEVICE NETWORK WIRING TOPOLOGIESFeatures and Specifications WelcomeC H A P T E R PC3500TX NOTICE - For Firmware 177B and EarlierPower Surges and Spikes Note about Lithium BatteryMount the Terminal Pre-Terminal InstallationMounting the Terminal To install the mounting bracket Turn the key clockwise to lock the terminal in place Connect the Communication Cable Setup the Terminal Starting the Test and Setup ModeSubnet Mask Network Test Not UsedPlug the terminal 12VDC power supply into the power connector To power up the terminal8 - PC3500TX Terminal Installation & User’s Guide Setup Mode - 177B Firmware For PayClock Pro 3.355G and earlier To Setup the PC3500TX’s Ethernet CommunicationsHIT ENTER IF DEFAULT ROUTE REQUIRED TERMINAL IP ADDRESS ###. ###. ###. ###HOST IP ADDRESS ###. ###. ###. ### NETWORK MASK ###. ###. ###. ###ENETADD=XXXXXXXXXXXX SETUP COMPLETE TCP/IP Conn. Type Setup Mode - 177G Firmware For PayClock Pro 4.1 and laterEnet MAC Address XXXXXXXXXXXX Default Router? TCP/IP Conn. ModeEnter Socket Port # Enter Terminal IP ###. ###. ###. ###Enter Sub Net Mask ###. ###. ###. ### Enter Keepalive ModeTest Mode To start the Test Mode“TEST MODE” PROG# TEST MODE 128 YYBattery Test BATTERY TEST PASS ENTER TO RETESTNote If you do not have a battery installed, the test will fail SWITCH TEST SWITCH TO USE POSITIONUnlocking Your Terminal Through Terminal Manager Restart ModeTo restart the terminal PRESS ENTER TO CLEAR ALL TRANSACTION DATAUse the Terminal To punchTo transfer To start a New DayTo enter amounts To review your last punchWhen you see BADGE FOR SUPERVISOR OVERIDE, swipe your badge When you see ENTER ASSOCIATES BADGE, swipe the employee’s badgeSupervisor Functions To see employee InfoInstall/Replace the Optional Backup Battery A P P E N D I X AOptional Signal Device GENERAL SPECIFICATIONSTo connect your signaling devices A P P E N D I X BA P P E N D I X C Network Wiring TopologiesTypical Lan network configuration Typical Wan network configuration 24 - PC3500TX Terminal Installation & User’s GuideTroubleshooting the Terminal 26 - PC3500TX Terminal Installation & User’s Guide Problem The terminal is not communicating with the computerProblem A previously working terminal now is not operational Reason TEST/USE switch is not in the Use positionProblem The terminal does not accept badge data Reason Bar code badge is not manufactured to specificationsSolution Refer to vendor’s manufacturing specifications Solution Ensure the badge stripe faces away from the keypad28 - PC3500TX Terminal Installation & User’s Guide Solution Open the PC3500TX’s Terminal Properties in Terminal ManagerClick OK to save the changes Update the terminal with the changes Select the Advanced tabTerminal Data Sheet A P P E N D I X D