Mitsubishi Electronics HS-S8300E(BRS) Setting the Menus, Recording SET UP, Rear Terminal

Page 10

SETTING THE MENUS

RECORDING SET UP

1SETTING THE ALARM REC MODE (ALARM REC MODE)

Sets the alarm recording time mode. When the JOG dial is turned, the display will be switched in the order of 3H } L12H } L24H } 3H } ....

2SETTING THE ALARM REC DURATION (ALARM REC DURATION)

Sets the duration of the alarm recording period. When the JOG dial is turned, the display will be switched in the order of 1M(minute) } 2M } 5M } 10M } MAN1 } MAN2 } 15S(second) } 30S } 45S } 1M } .... Refer to “ALARM RECORDING” on page 22.

3SETTING THE EMERGENCY REC (EMERGENCY REC)

<RECORDING SET UP>

3H

ALARM REC MODE

ALARM REC DURATION

1M

EMERGENCY REC

OFF

ONESHOT•FIELD

1

ONESHOT•INTERVAL

SHOT

 

 

Sets the emergency recording mode.

OFF: Starts alarm recording when the alarm signal is received during recording.

ON: Starts alarm recording when the alarm signal is received not only during recording but also when the power is OFF or when the tape is stopped.

N

•When “ON” is selected, the alarm recording begins even though the recorder is in recording standby mode.

4SETTING THE NUMBER OF FIELDS IN ONE-SHOT RECORDING (ONE SHOT•FIELD)

Sets the number of recorded fields in the one-shot recording mode. When the JOG dial is turned to the right, the display will be switched in the order of 1 } 2 } 3 } 4 } 5 } 10 } 20 } 30 } 1 }....

5SETTING THE INTERVAL TIME IN THE ONE-SHOT RECORDING MODE (ONE SHOT•INTERVAL)

Sets the interval time in the one-shot recording mode. When the JOG dial is turned to the right, the display will be switched in the order of SHOT } 10S (second) } 15S } 30S } 45S } 1M } 2M } 3M } SHOT }....

REAR TERMINAL

1SETTING THE CALL SIGNAL OUTPUT AT THE END OF THE TAPE (CALL OUT)

Enables or disables the signal that is output from the CALL terminal when the end of the tape is reached during recording. If any abnormalities occur during recording, a CALL signal is output from the CALL terminal on the rear panel regardless of CALL OUT setting.

WRNG•TAPE END:

A signal is output at the end of the tape or when a malfunction occurs.

WRNG•REMAIN:

The signal is output when a malfunction occurs in this VCR or when the

 

tape has approximately 3 minutes left in 3H mode.

WRNG:

When a malfunction occurs in the VCR during recording, a CALL signal is

 

output.

<REAR TERMINAL>

CALL OUT

WRNG•TAPE END

CLOCK OUT

REC- 1

MODE OUT

REC

REC IN

SERIES

This is used in conjunction with TAPE END (FIRST TIME SET UP) to determine when the CALL signal is output as shown below.

CALL OUT

TAPE ENDsetting setting

STOP

REWIND

REPEAT

WRNG•TAPE END

Outputs a call signal at the

end of the tape

Outputs a call signal at the end of the tape for 2 seconds

WRNG•REMAIN

Outputs 3 minutes before

the tape end

WRNG

When a malfunction occurs in the VCR during recording, a call signal is output.

When there are no ALARM alarm recordings during recording

• PROT

When there are alarm Outputs a call signal at the

recordings duringend of the tape recording

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents HS-S8300EBRS VHSCondensation is the Enemy of Video Recorders When not in USEInstallation Location Unplugging the Mains LeadContents FeaturesFront View Features and FunctionsFluorescent display REC Fluorescent DisplayReset button Features and FunctionsRear View Connecting with Other Equipment SensorPresent time display will appear Setting the MenusPresent Time Display Display Timer ProgramTime Date Search Recording SET UP Setting the MenusRear Terminal Maintenance First Time SET UP Display mode Setting the Present TimeFRI Setting the Present Time Setting the Present Time to the Exact SecondUnloading Loading and Unloading the Cassette TapeLoading Preventing Accidental ErasureManual Recording REC ModeLock Mode Recording Check FunctionNumber of Tape USE Repeat REC Times Stop Rewind Repeat AlarmprotRepeat Recording Recommended Number of Tape USESynchronous Recording Manual RecordingONE SHOT/INTERVAL Recording ConnectionAdditional Features Timer Recording Order to Avoid Mistakes When Using the Timer Symptom Fault ActionExternal Time Clock Adjustment Alarm RecordingAlarm Recording Connection 1st VCRSetting for Alarm Recording Emergency RecordingLocating the Start of Alarm Recordings Alarm RecordingAlarm Record Time Display Index SearchPlayback Playback ModeAudio Playback Direct Shuttle Ring Special Effects PlaybackShuttle Ring Still PicturePicture Quality Adjustment Adjustment During PlaybackTracking Adjustment When the picture is vibratingConfiguring the Time Lapse VCR Using with the Personal ComputerConnecting the VCR to a personal computer Setting Data BIT Length RS-232C SettingSetting Transmission Rate Setting Stop BIT LengthData Communications Settings Using with the Personal ComputerConnecting to a Personal Computer Physical protocol of RS-232CCommand received Command Commands sent to the VCR FormatPower on command Command carried outCommand received VCR02 Command ParameterCommand for fast forwarding VCR02 Command carried out VCR02Commands and Responses 171=TIME Date Adjust + STOP=0, REWIND=1, REPEAT=2 Error codes +0=SERIES, 1=REC-START/STOP =SYNC RECCause Remedy To Turn OFF the Indication Self Diagnostic FunctionFluorescent Monitor DisplaySymptom Remedy Before Calling for ServiceIs the Lock indicator illuminated? Control INPUT/OUTPUT Signals and Circuits Circuit Control INPUT/OUTPUT Signals and CircuitsLabel B-7 Specifications Connectors872C193C3
Top Page Image Contents