Mitsubishi Electronics HS-S8300E(BRS) Setting for Alarm Recording, Emergency Recording

SETTING FOR ALARM RECORDING

Alarm Recording is used to activate more rapid recording when the VCR is recording in one of the Time Lapse modes. Alarm Recording provides for more pictures during the Alarm duration. Emergency Recording enables Alarm Recording even if the VCR is off, stopped or in Timer Recording/Standby. You should set the Alarm Recording mode with the “RECORDING SET UP” menu before Alarm Recording is used.

1	Press the DISPLAY button to display MAIN MENU on the monitor.	<MAIN MENU>
		DISPLAY
2	Turn the JOG dial to select “RECORDING SET UP”	TIME DATE SEARCH
		TIMER PROGRAM
	and turn the SHUTTLE ring to the right.	RECORDING SET UP
		REAR TERMINAL
	• “RECORDING SET UP” menu will appear.	MAINTENANCE
		FIRST TIME SET UP
		Use JOG to select,
3	Turn the JOG dial to select “ALARM REC MODE” and	and ENTER.
	turn the SHUTTLE ring to the right.	Press DISPLAY to exit.
4
	Turn the JOG dial to set the alarm recording mode
		<RECORDING SET UP>
	and turn the SHUTTLE ring to the right.		3H
		ALARM REC MODE
		ALARM REC DURATION	1M
5	Turn the JOG dial to select “ALARM REC DURATION” and	EMERGENCY REC	OFF
	turn the SHUTTLE ring to the right.
6	Turn the JOG dial to set the alarm recording duration from 15 seconds to 10 minutes, MAN1 or
		<RECORDING SET UP>
	MAN2 (manual). When the desired setting is shown, turn the SHUTTLE ring to the right.		3H
		ALARM REC MODE
	• If the “ALARM REC DURATION” is set to “MAN1”, alarm recording will continue until a signal	ALARM REC DURATION	1M
		EMERGENCY REC	OFF
	is applied to the RST (RESET) IN terminal. If the signal applied to the RST (RESET) IN
	terminal is within the first 15 seconds of alarm recording, alarm recording will continue for 15
	seconds, then stop.

•If the “ALARM REC DURATION” is set to “MAN2”, alarm recording will continue until the signal applied to the SET IN terminal is removed. If the signal applied to the SET IN terminal is removed within 15 seconds of the start of alarm recording, alarm recording will continue for 15 seconds, then stop.

•The internal time clock can be adjusted if a signal is applied to the RST (RESET) IN terminal on the rear panel when the ALARM REC DURATION is set to other than “MAN1”.

7Turn the JOG dial to select “EMERGENCY RECORDING” and turn the SHUTTLE ring to the

right.	<RECORDING SET UP>
• Turn the JOG dial to select “ON”.		3H
	ALARM REC MODE
	ALARM REC DURATION	1M
8 Press the DISPLAY button.	EMERGENCY REC	ON

•The present time display will appear.

^During alarm recording, the alarm recording count will automatically be displayed except when DISPLAY mode “4” is selected.

•The alarm recording count display counts up to 9999 alarm recordings and then it is reset to 0000 and continues counting.

•When initializing the alarm recording list, the alarm recording count display will be reset.

•The alarm indicator flashes during alarm recording and lights up when the alarm recording is finished.

•When the alarm recording is finished, the VCR resumes recording in the same record modes as before the alarm recording.

N

•If a set signal is applied during alarm recording, a new alarm recording will start with the new set signal. Should one SET signal be applied within 15 seconds of another, the later SET signal will be ignored and a new alarm recording will not take place.

•Alarm recording will continue for the duration of time which has been set in the “ALARM REC DURATION” menu, even if a timer recording has reached its end time.

•Alarm recording stops when the end of the tape is reached.

EMERGENCY RECORDING

Emergency Alarm Recording can start recording when an Alarm is triggered even if the VCR is off, stopped or in Timer Recording/ Stand-by. Turn the JOG dial to select “EMERGENCY RECORDING” and turn the SHUTTLE ring to the right.

Turn the JOG dial to select “ON” to select Emergency Recording, or “OFF” to disable it.

•“EMGCY” lights up on the fluorescent display when the “EMERGENCY REC” of the “RECORDING SET UP” menu is set to “ON”.

23