Mitsubishi Electronics HS-S8300E(BRS) Control INPUT/OUTPUT Signals and Circuits, Label B-7

Page 40

CONTROL INPUT/OUTPUT SIGNALS AND CIRCUITS

2REMOTE jack

Circuit

Shielded

MJ cable R R

SW

SW

R

SW

SW

				1	2 ····································31 32
1)Resistor R:			Metal film resistor 1/4W 33kohms ±1%,
			temperature factor ±100ppm/°C.
2)Button switch:			Momentary, ON resistor 200ohms or under.
3)Connector MJ:			Miniature jack, 2.5mm in diameter, comply with JISC6560.
Operational conditions
1)Isolation resistor:			200Mohms or over (in connector MJ)
2)Floating capacity:			0.1µF or under (in connector MJ).
3)Environmental temperature:			5-40°C (common with VCR).
4)Relative temperature:			Max. 80% (common with VCR).
				Remote control switch functions

Position	Function		Position	Function		Position	Function	Position	Function
1	STOP		9	3H		17	POWER ON/OFF	25	DOWN POSITION/SHIFT
2	RECORDING		10	L24H		18	REVERSE FRAME SHIFT	26	UP POSITION/SHIFT
3	PAUSE		11	48H		19	TIME DATE SEARCH	27	CLEAR
4	PLAYBACK		12	72H		20	INDEX SEARCH	28	START/END
5	REVERSE PLAYBACK		13	120H		21	( )DISPLAY/SET	29	( )REC/PLAY MODE
6	FORWARD FRAME SHIFT		14	240H		22	(+)DISPLAY/SET	30	(+)REC/PLAY MODE
7	FAST FORWARD		15	0H		23	LEFT POSITION/SHIFT	31	SKIP SEARCH
8	REWIND		16	–		24	RIGHT POSITION/SHIFT	32	TIMER RECORDING

2Remote Control (optional)

The optional Remote Control (R-7100) provides remote operation of the VCR.

Before using the remote control, put the label on it as shown in Fig.

No function is available.

REC/PLAY MODE
Label (B-7)
3H	L24H

PLAY

STOP

REC				PAUSE
				/STILL
				/STILL

REV				FR ADV
PLAY

/REW FF/

40

Image 40

Contents HS-S8300EBRS VHSWhen not in USE Installation LocationCondensation is the Enemy of Video Recorders Unplugging the Mains LeadContents FeaturesFront View Features and FunctionsFluorescent display REC Fluorescent DisplayReset button Features and FunctionsRear View Connecting with Other Equipment SensorPresent time display will appear Setting the MenusPresent Time Display Display Timer ProgramTime Date Search Recording SET UP Setting the MenusRear Terminal Maintenance First Time SET UP Display mode Setting the Present TimeFRI Setting the Present Time Setting the Present Time to the Exact SecondLoading and Unloading the Cassette Tape LoadingUnloading Preventing Accidental ErasureREC Mode Lock ModeManual Recording Recording Check FunctionStop Rewind Repeat Alarmprot Repeat RecordingNumber of Tape USE Repeat REC Times Recommended Number of Tape USEManual Recording ONE SHOT/INTERVAL RecordingSynchronous Recording ConnectionAdditional Features Timer Recording Order to Avoid Mistakes When Using the Timer Symptom Fault ActionAlarm Recording Alarm Recording ConnectionExternal Time Clock Adjustment 1st VCRSetting for Alarm Recording Emergency RecordingAlarm Recording Alarm Record Time DisplayLocating the Start of Alarm Recordings Index SearchPlayback Playback ModeAudio Playback Special Effects Playback Shuttle RingDirect Shuttle Ring Still PictureAdjustment During Playback Tracking AdjustmentPicture Quality Adjustment When the picture is vibratingConfiguring the Time Lapse VCR Using with the Personal ComputerConnecting the VCR to a personal computer RS-232C Setting Setting Transmission RateSetting Data BIT Length Setting Stop BIT LengthUsing with the Personal Computer Connecting to a Personal ComputerData Communications Settings Physical protocol of RS-232CCommand Commands sent to the VCR Format Power on commandCommand received Command carried outCommand Parameter Command for fast forwarding VCR02Command received VCR02 Command carried out VCR02Commands and Responses 171=TIME Date Adjust + STOP=0, REWIND=1, REPEAT=2 Error codes +0=SERIES, 1=REC-START/STOP =SYNC RECSelf Diagnostic Function Fluorescent MonitorCause Remedy To Turn OFF the Indication DisplaySymptom Remedy Before Calling for ServiceIs the Lock indicator illuminated? Control INPUT/OUTPUT Signals and Circuits Circuit Control INPUT/OUTPUT Signals and CircuitsLabel B-7 Specifications Connectors872C193C3